Kikusui PCZ1000A Скачать руководство пользователя

Страница: 11 / 100

PCZ1000A

Appx.

3.5.1

CC Mode Operation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-11

3.5.2

Constant Resistance (CR) Mode - - - - - - - - - - - - - - - - - - - - - - - - 3-12

3.5.3

Constant Power (CP) Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-15

3.5.4

Crest Factor Function - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-16

3.6

Saving and Recalling Preset Memory - - - - - - - - - - - - - - - - - - - - - - - - - - 3-17

Saving Preset Memory  - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -  3-18
Changing Preset Memory  - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -  3-19
Recalling Preset Memory   - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -  3-20

3.7

Parallel Operation and Tracking Operation - - - - - - - - - - - - - - - - - - - - - - - 3-21
3.7.1

Configuration (CONFIG) Settings - - - - - - - - - - - - - - - - - - - - - - - - 3-21

How to Display and Set Configuration Settings - - - - - - - - - - - - - - - - - 3-22

3.7.2

Parallel Operation- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-23

Procedure for Connecting Units in Parallel- - - - - - - - - - - - - - - - - - - - - 3-24
Procedure for Setting Master and Slave Units - - - - - - - - - - - - - - - - - - 3-25

3.7.3

Tracking Operation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-27

Connecting Units for Tracking Operation - - - - - - - - - - - - - - - - - - - - - - 3-28
Procedure for Setting Master and Slave Units - - - - - - - - - - - - - - - - - - 3-28

3.7.4

Calibration of the Ammeter on the Master Unit During Parallel Operation
3-30

Preparation for Calibration - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-30
Calibration Procedure - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-31

3.7.5

Alarms During Parallel and Tracking Operation - - - - - - - - - - - - - - 3-33

3.7.6

Returning to Standalone Operation - - - - - - - - - - - - - - - - - - - - - - 3-33

3.8

Factory Default Settings - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-34

Chapter 4 Remote Control

4.1

Overview of Remote Control - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-2
4.1.1

RS232C Interface - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-2

4.2

Programming Format - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-4
4.2.1

Program Messages- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-4

4.3

Device Messages - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-5
4.3.1

Program Header and Program (Response) Data - - - - - - - - - - - - - - 4-5

4.3.2

Configuration of Device Messages - - - - - - - - - - - - - - - - - - - - - - - - 4-6

Basic Messages - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -  4-6
System Messages- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -  4-8
Communication Settings and Control Codes  - - - - - - - - - - - - - - - - - - - -  4-8

4.4

Assignment of Register Bits - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-9

Fault Register   - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -  4-9
Fault Register 2  - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -  4-9
Error Register   - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -  4-10
Communication Command Errors   - - - - - - - - - - - - - - - - - - - - - - - - - -  4-10

Chapter 5 Maintenance and Calibration

5.1

Cleaning and Inspection - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-2

Inspecting the Power Cord - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-2
Cleaning the Panel - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-2

Содержание PCZ1000A





































































































Результаты поиска

Содержание PCZ1000A

Отзывы:

Похожие инструкции для PCZ1000A

Бренды по названию

Популярные бренды

Kikusui PCZ1000A, Руководство по эксплуатации

Результаты поиска

Содержание PCZ1000A

Отзывы:

Похожие инструкции для PCZ1000A

Бренды по названию

Популярные бренды