Kikusui PCZ1000A Скачать руководство пользователя | Manualshive

Страница: 40 / 100

background image

3-6

PCZ1000A

Turning off the POWER switch

Turn the POWER switch to OFF ( ).
The  backup  function  of  the  PCZ1000A  saves  the  following  settings  when  the
POWER switch is turned off.
When the power is turned off, the PCZ1000A automatically memorizes and saves
the  settings  (setup)  that  are  in  use.  The  settings  and  initial  values  saved  by  this
function are listed below. Those in parentheses are initial values.

•

ISET value

•

RSET value

•

PSET value

•

CREST FACTOR value

•

Range in the CR mode

•

C.F on/off

•

Contents of memories A, B, and C

•

CONFIG setting

The load on/off state is not stored. The PCZ1000A always starts up with the load
turned off when the power is turned on.

If the PCZ1000A is not turned on with the condition of the last setting when the
POWER switch was turned off, the life of back-up battery may be dead.

3.3

Load-On/Load-Off

The PCZ1000A switches between the load-on and load-off states each time the
LOAD key is pressed. If the protection function operates, the PCZ1000A goes to
load-off automatically.

• Load-on:

Load current is on

The LED above the LOAD key illuminates.

• Load-off:

Load current is disconnected

The LED above the LOAD key turns off.

• Risk of damage to the PCZ1000A. Only connect the output of the

equipment under test to the PCZ1000A input when it is set to the load-off
state. Do not change to load-on until after connecting. If you do connect
to  the  PCZ1000A  input  when  it  is  in  the  load-on  state,  ensure  that  the
output for the equipment under test is turned off.

If a relay, electromagnetic circuit breaker, or similar is connected between
the  output  terminals  of  the  equipment  under  test  and  the  load  input
terminals,  only  turn  the  relay  or  circuit  breaker  on  when  in  the  load-off
state and do not change to load-on until after turning on the input.

See

CAUTION

«
...
38
39
40
41
42
...
»

Содержание PCZ1000A





































































































Отзывы:

Нет отзывов

Похожие инструкции для PCZ1000A

Ettan IPGphor 3

Бренд: GE Страницы: 64

Бренд: GE Страницы: 56

Бренд: GE Страницы: 132

Бренд: GE Страницы: 16

Бренд: GE Страницы: 474

Бренд: Napoleon Страницы: 2

Бренд: Raytheon Страницы: 62

Бренд: Dairyland Страницы: 21

Litmann Quality 3100

Бренд: 3M Страницы: 2

Бренд: Baker Страницы: 82

Бренд: Water Witch Страницы: 2

Бренд: Falltech Страницы: 48

Бренд: Mangar International Страницы: 8

Бренд: Malvern Instruments Страницы: 30

Бренд: zarges Страницы: 36

Бренд: Parker Страницы: 24

Бренд: Abus Страницы: 8

Monster Truck Headboard 41903

Бренд: Simplay3 Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды