manualshive.com logo in svg

Kikusui PCZ1000A, Руководство по эксплуатации

Описание продукта "Kikusui PCZ1000A": Это мощный и надежный источник питания, который можно настроить для различных экспериментов и испытаний. Вы можете бесплатно загрузить Руководство по эксплуатации с manualshive.com, чтобы получить полное представление о функциях и возможностях этого прибора.

Поделиться
Скачать
background image

PCZ1000A

6-3

6

S

pecifications

Voltmeter

Number of display digits (full scale) 

300.0 Vrms

Accuracy

*6

Within 

±

 1 % of FS

Protection function

*17

Peak overcurrent protection (POCP)

*18

Approx. 48 Apeak

Overcurrent protection (OCP)

*19

Approx. 11.5 Arms

Overvoltage protection (OVP)

*18

Approx. 470 Vpeak

Overpower protection (OPP)

Approx. 1 150 W

Overheat protection (OHP)

*20

−

Internal circuit protection(FUSE BRK)

Internal fuse blown

External alarm 1 (EXT1)

Another unit has detected an alarm during 
parallel or tracking operation.

External alarm 2 (EXT2)

Alarm detected when the PC01-PCZ1000A 
flat cable comes unplugged during parallel or 
tracking operation (only on slave units that 
become disconnected from the master).

Input power (AC) 

Voltage range (nominal value)

*21

90 Vrms to 110 (100) Vrms
108 Vrms to 132 (120) Vrms
180 Vrms to 220 (200) Vrms
216 Vrms to 250 (240) Vrms

Frequency

50 Hz/60 Hz

Power consumption (apparent power)

MAX 220 VA

*1.

Input-voltage range in which the rated input current can flow.

*2.

For an input voltage of 100 Vrms or greater, the maximum current is derated to the rated input                  
power (1 000 W).

*3.

For an input voltage of 100 Vrms or less, the maximum power is limited by the rated input                  
current (10 Arms).

*4.

Minimum input voltage at which the input current starts to flow

*5.

The input-current waveform does not change with changes in the input-voltage waveform.
The RMS value of the input current is kept constant (response rate: approximately 1 s).
(Response rate: Time required to reach 

±

10% of the steady value (value reached 5 seconds               

or more after state change))

*6.

At temperature(23 

±

 5 

°

C)

*7.

Changes in the input current when variations in the rated-voltage range are given at an input                
voltage of 100 Vrms and an input current of 10 Arms, based on the nominal value of the input                  
line voltage.

*8.

Changes in the input current when the input voltage is changed from 10 Vrms to 280 Vrms at                  
an input current of 3.57 Arms (rating at an input voltage of 280 Vrms).

*9.

The input-current waveform does not change with changes in the input-voltage waveform. 
This mode results in an input current (RMS value) that is proportional to the RMS value of the                 
input voltage (response rate: approximately 1 s).

*10. S represents the unit of conductance (siemens).

Conductance [S] = 1/resistance value [

Ω

]

Conductance [S] × input voltage [V] = load current [A]

*11. At an input voltage of 100 Vrms.
*12. Changes in the resistance value when the input voltage is varied from 10 Vrms to 100 Vrms                 

at an input current of 0.5 A or more.

*13. The input-current waveform does not change with changes in the input-voltage waveform.            

This mode results in an input current (RMS value) that is inversely proportional to the RMS

               

value of the input voltage (response rate: approximately 1 s).

*14. At an input voltage of 100 Vrms
*15. Changes in the power value when the input voltage is varied from 10 Vrms to 100 Vrms.
*16. Varies the angular width of the current at the approximate input-voltage peak, based on a               

sinusoidal current waveform.

*17. Turns off the LOAD key when the protection function is activated.
*18. Turns off the LOAD key within 20 ms.
*19. Turns off the LOAD key within 3 ms.
*20. Detects the internal-heat-sink surface temperature to turn off the LOAD key.
*21. Selectable by Switch position.

Содержание PCZ1000A





































































































Отзывы:

Нет отзывов

Похожие инструкции для PCZ1000A

Rath 2100 Installation & Operation Manual preview
2100
Бренд: Rath Страницы: 3
Harken T2 Instructions preview
T2
Бренд: Harken Страницы: 4
B-K lighting Precision2 HP2 Series Installation Instructions Manual preview
Precision2 HP2 Series
Бренд: B-K lighting Страницы: 6
Zero Hand Truck Pro Handbook preview
Pro
Бренд: Zero Hand Truck Страницы: 38
B-K lighting Altair Quick Manual preview
Altair
Бренд: B-K lighting Страницы: 3
NEILPRYDE RS6 Manual preview
RS6
Бренд: NEILPRYDE Страницы: 55
HANYOUNGNUX STE Series Instruction Manual preview
STE Series
Бренд: HANYOUNGNUX Страницы: 4
Park House Healthcare WARWICK User Manual preview
WARWICK
Бренд: Park House Healthcare Страницы: 6
J&M TF2 Operator'S Manual preview
TF2
Бренд: J&M Страницы: 33
TATU PT Operator'S Manual preview
PT
Бренд: TATU Страницы: 30
Rane HC6S Operator'S Manual preview
HC6S
Бренд: Rane Страницы: 4
Sabio 2010D Operation Manual preview
2010D
Бренд: Sabio Страницы: 182
Velp Scientifica REC Instruction Manual preview
REC
Бренд: Velp Scientifica Страницы: 16
Velp Scientifica AREX-6 How To Connect preview
AREX-6
Бренд: Velp Scientifica Страницы: 2
Velp Scientifica AREC.X Operating Manual preview
AREC.X
Бренд: Velp Scientifica Страницы: 32
Velleman-Kit EDU08 Manual preview
EDU08
Бренд: Velleman-Kit Страницы: 32
XFit TARGET User Manual preview
TARGET
Бренд: XFit Страницы: 16
Nakamichi BlackBox Series Service Manual preview
BlackBox Series
Бренд: Nakamichi Страницы: 23

Бренды по названию

Популярные бренды

Загрузить еще бренды