Kikusui PCZ1000A Скачать руководство пользователя

Страница: 7 / 100

PCZ1000A

Grounding

• This product is an IEC Safety Class I device (device with protected

conductor terminals). To prevent electric shock, be sure to connect the

protective conductor terminal of the product to electrical ground
(safety ground).

Installation

• This product is designed for safe indoor use. Only use the product

indoors.

• Please read the section 2.2, “Precautions for Installation” section of

this manual before installing the product and comply with the

instructions.

Relocation

• Turn off the POWER switch, and disconnect the cables before

relocating the product.

• The product weighs over 20 kg. When moving the product, have more

than one person carry it. The weight of the product is indicated on the

rear panel of the product and in the specification table in this manual.

• When relocating the product, remember to also relocate the manual.

Operation

• Before using the product, be sure to check the input power voltage and

that there is no abnormality in the appearance of the AC power cord.
Be sure to remove the power cord plug from the outlet before checking.

• If a malfunction or abnormality is detected on the product, stop using it

immediately, and remove the power cord plug from the outlet. Make

sure the product is not used until it is completely repaired.

• Use cables or wires with sufficiently large current capacity for output

wires and load cables.

• Do not disassemble or modify the product. If you need to modify the

product, contact your Kikusui distributor or agent.

Maintenance
and inspection

• To prevent electric shock, be sure to turn off the switchboard breaker

before carrying out maintenance or inspection.

• Do not remove the external cover during maintenance or inspection.
• To maintain the performance and safe operation of the product, it is

recommended that periodic maintenance, inspection, cleaning, and

calibration be performed.

Service

• Kikusui service engineers will perform internal service on the product.

If the product needs adjustment or repairs, contact your Kikusui
distributor or agent.

G N L

Check?

Содержание PCZ1000A





































































































Результаты поиска

Содержание PCZ1000A

Отзывы:

Похожие инструкции для PCZ1000A

Бренды по названию

Популярные бренды

Kikusui PCZ1000A, Руководство по эксплуатации

Результаты поиска

Содержание PCZ1000A

Отзывы:

Похожие инструкции для PCZ1000A

Бренды по названию

Популярные бренды