Kikusui PCZ1000A Скачать руководство пользователя

Страница: 62 / 100

3-28

PCZ1000A

Connecting Units for Tracking Operation

Risk of electric shock
• Turn off the POWER switch when you are touching the load input

terminals, PARALLEL IN connector, or PARALLEL OUT connector.
Also, re-attach the load input terminal cover after connecting the
cables.

• Always fit the protective socket when not using the PARALLEL IN

connector or PARALLEL OUT connector.

Risk of damage to the PCZ1000A.

• Take care not to get the PARALLEL IN connector and PARALLEL OUT

connector mixed up.

• Ensure that the load cable is as short as possible with a sufficient cross

section for the current level being used.

• Ensure that the insulation on the load cable you use has good fire resistance.
• Ensure that the cables to the load input terminals on each of the PCZ1000A are

as similar in length as possible.

Turn off the POWER switch.

Connect the cables to the load input terminals.

Referring to the connection diagram in Fig.3-10, connect the cables to the load input
terminals on each unit (which must all be of the same model).

Connect the parallel operation connector.

Use the option flat cable (PC01-PCZ1000A) to connection between the PARALLEL

OUT and PARALLEL IN connectors on each unit.

Procedure for Setting Master and Slave Units

Turn on the POWER switch on each unit.

Either turn on the POWER switch on all units at the same time or turn on the master
unit first.

• If the power to the slaves is turned on first, turn on the POWER switch of the

master unit within 30 seconds. An external alarm 2 occurs if this time is longer
than 30 seconds.

Press the LOAD key to go to the load-off state.

Press SHIFT + I SET(CONFIG).

Use the ENTER key to select ">1:Norm /M/S".

WARNING

CAUTION

Содержание PCZ1000A





































































































Результаты поиска

Содержание PCZ1000A

Отзывы:

Похожие инструкции для PCZ1000A

Бренды по названию

Популярные бренды

Kikusui PCZ1000A, Руководство по эксплуатации

Результаты поиска

Содержание PCZ1000A

Отзывы:

Похожие инструкции для PCZ1000A

Бренды по названию

Популярные бренды