Kikusui PCZ1000A Скачать руководство пользователя | Manualshive

Страница: 58 / 100

background image

3-24

PCZ1000A

Procedure for Connecting Units in Parallel

Parallel operation requires connection of a signal cable between the loads and a load
cable that connects to the equipment under test.
For the signal cable, always use the flat cable (PC01-PCZ1000A) available as an
option. Use load cables for the connection from the PCZ1000A to the equipment
under test.

Fig.3-9 Flat Cable for Parallel Operation, Available as an Option

Risk of electric shock
• Turn off the POWER switch when you are touching the load input

terminals, PARALLEL IN connector, or PARALLEL OUT connector.
Also, re-attach the load input terminal cover after connecting the
cables.

• Always fit the protective socket when not using the PARALLEL IN

connector or PARALLEL OUT connector.

• If the flat cable used for parallel operation becomes disconnected

during parallel or tracking operation, turn off the POWER switch on

each unit before reconnecting.

Risk of damage to the instrument

•

Take care not to get the PARALLEL IN

connector and

PARALLEL OUT

connector mixed up.

•

Ensure that the load cable is as short as possible with a sufficient cross-
section area for the current level being used.

• Note that the ammeter (RMS, peak) on the master unit will not display correctly

if the flat cable used for parallel operation becomes disconnected during parallel
or tracking operation.

• Ensure that the insulation on the load cable you use has good fire resistance.
• Ensure that the cables to the load input terminals on each PCZ1000A are as

similar in length as possible.

1

Turn off the POWER switch.

2

Connect the cables to the load input terminals.

Referring to the connection diagram in Fig.3-8, connect the cables to the load input
terminals on each unit (which must all be of the same model).

3

Connect the parallel operation connector.

Use the option flat cable (PC01-PCZ1000A) to connection between the PARALLEL

OUT and PARALLEL IN connectors on each unit.

WARNING

CAUTION

«
...
56
57
58
59
60
...
»

Содержание PCZ1000A





































































































Отзывы:

Нет отзывов

Похожие инструкции для PCZ1000A

Бренд: Tanco Страницы: 112

Бренд: Radial Engineering Страницы: 2

Бренд: Radial Engineering Страницы: 2

Бренд: TATU Страницы: 30

Бренд: Rane Страницы: 4

Бренд: Sabio Страницы: 182

Бренд: Yamaha Страницы: 178

Бренд: Yamaha Страницы: 15

Бренд: Zero 88 Страницы: 12

Бренд: Zest4Leisure Страницы: 4

Бренд: Zeiss Страницы: 119

Бренд: Zehnder Rittling Страницы: 32

Бренд: IBC Страницы: 4

Spielturm Premium L GP1122

Бренд: gartenpirat Страницы: 8

Lisa-Fun GP1604

Бренд: gartenpirat Страницы: 6

Бренд: B&G Страницы: 16

ResQCRP ResQPUMP ACD-CPR

Бренд: Advanced Circulatory Страницы: 2

Big Wheel RN1 Series

Бренд: Osborne Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды