Kikusui PCZ1000A Скачать руководство пользователя | Manualshive

Страница: 44 / 100

background image

3-10

PCZ1000A

3.5

Operation Modes

The PCZ1000A has the following four operation modes. The crest factor function is
also available in constant-current mode.

•

Constant-current mode (CC mode)

•

Constant-resistance mode (CR mode)

•

Constant-power mode (CP mode)

•

Constant-c Crest Factor function

Operation Mode Display

The currently selected operation mode is indicated by the LEDs on the operation
panel.

CC mode:

The C.C LED above the I SET key illuminates.

CR mode:

The C.R LED above the R SET key illuminates.

CP mode:

Both the C.C and C.R LEDs illuminates.

CF function:

The C.F LED above the C.F key illuminates. Because the

CREST FACTOR function is only used in CC mode, the C.C

LED also illuminates.

If the operating point of the PCZ1000A is limited by an operation mode other than
the selected mode, the relevant LED blinks.

C.C LED blinks: The PCZ1000A is operating in the CP range even though CC

mode is selected.

C.R LED blinks: The PCZ1000A is operating in the CC or CP operation range

even though CP mode is selected.

CC and CP LEDs both blink:

The PCZ1000A is operating in the CC operation range even

though CP mode is selected.

• In CP mode, the PCZ1000A may not reach the CP operation range and may

operate in the CC operation range if the input voltage is low. This causes both the
C.C and C.R LEDs to blink. For example, when 1 000 W is set as the PSET value
and 10 A is set as the ISET value, the instrument will not enter the CP operation
range unless the input voltage is 100 Vrms or more. In the same way, when the
PSET  value  is  140  W,  the  PCZ1000A  will  not  enter  the  CP  operation  range
unless  the  input  voltage  is  14  Vrms  or  more.  In  the  range  in  which  the  input
voltage is 10 V rms or less, the PCZ1000A is unable to sink its maximum current
(10 Arms; see "Operation range of the PCZ1000A" above). Thus, even when a
current of the ISET value or less flows, the PCZ1000A apparently operates in the
CC operation range, causing both the C.C and C.R LEDs to blink. In particular,
near  an  input  voltage  of  0  Vrms,  the  CC  operation  current  becomes  almost  0
Arms. This causes both the C.C and C.R LEDs to blink, even when no power
supply under test is connected to the PCZ1000A.

«
...
42
43
44
45
46
...
»

Содержание PCZ1000A





































































































Отзывы:

Нет отзывов

Похожие инструкции для PCZ1000A

Бренд: MAHLE Страницы: 21

Бренд: Keithley Страницы: 42

Бренд: Parker Страницы: 5

Бренд: Bacharach Страницы: 31

Бренд: Backyard Play Systems Страницы: 52

Бренд: Backyard Play Systems Страницы: 19

Бренд: Backyard Play Systems Страницы: 44

Бренд: Bacharach Страницы: 2

Бренд: LAWO Страницы: 459

Бренд: earline Страницы: 13

The Wave Transformer

Бренд: EarthQuaker Devices Страницы: 21

Бренд: Masterclock Страницы: 19

Бренд: Coba Страницы: 2

Бренд: Axi Страницы: 27

Бренд: Neilsen Страницы: 8

Бренд: Crivit Outdoor Страницы: 20

Бренд: REV Ritter Страницы: 11

Бренд: Max Tapener Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды