Kikusui PCZ1000A Скачать руководство пользователя | Manualshive

Страница: 55 / 100

background image

PCZ1000A

3-21

3

Ope

ration

3.7

Parallel Operation and Tracking Operation

Parallel operation

It is possible to increase the current and power capacity by connecting a number of
PCZ1000As in parallel. Up to four PCZ1000As can be connected in parallel with
one unit acting as the master unit and the others as slave units. The master unit acts
as the master to control the other slave units.

Tracking operation

Tracking  operation  means  that  the  setting  values  specified  on  the  master  unit  are
also  applied to the slave units, and any  changes  to  the  master settings  also  apply
simultaneously to the slaves. Up to four PCZ1000As can be connected in parallel
with one unit acting as the master unit and the others as slave units.
This function is useful for testing single-phase/three-wire or three-phase/three-wire
AC power supplies.

Parallel operation and tracking operation cannot be used in the following
combinations.

• Combination with PCZ1000As and PCZ1000s (older models).
• Combination with PCZ1000As with firmware version 1.40 or later and

PCZ1000As with less than version 1.40.

3.7.1

Configuration (CONFIG) Settings

The operation of the PCZ1000A can be set to standalone operation, parallel
operation, tracking operation, or total current calibration by the configuration
setting.
Pressing the SHIFT + I SET (CONFIG) key brings up the configuration screen.
The following configuration settings are available.

Table3-1 CONFIG Settings List

No.

Setting

Setting Values

Related Sections

1

Norm /M/S

NORMAL, MASTER,
SLAVE

Standalone operation,
parallel operation, tracking
operation

2

Para /Track

PARALLEL, TRACKING

Parallel operation, tracking
operation

3

Parallel Ope.

2, 3, 4, 5

Parallel operation

4

Calibration

Push [I SET]

Parallel operation

«
...
53
54
55
56
57
...
»

Содержание PCZ1000A





































































































Отзывы:

Нет отзывов

Похожие инструкции для PCZ1000A

SafetuNet Alert

Бренд: Masimo Страницы: 2

Бренд: CAIRE Страницы: 2

Бренд: Wavetek Страницы: 74

Бренд: Fairchild Страницы: 16

Бренд: Keithley Страницы: 67

Бренд: Keithley Страницы: 23

Бренд: Keithley Страницы: 93

Бренд: Oki Страницы: 44

Бренд: Magnescale Страницы: 64

Бренд: Haigh Страницы: 60

Бренд: Panlux Страницы: 2

Бренд: Hach Страницы: 456

Бренд: ubicquia Страницы: 36

Бренд: Biosonic Страницы: 2

Бренд: Petzl Страницы: 7

RGB Studio Beam Driver

Бренд: SHOWTEC Страницы: 16

Бренд: American DJ Страницы: 12

Бренд: aion Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды