Kikusui PCZ1000A Скачать руководство пользователя

Страница: 50 / 100

3-16

PCZ1000A

3.5.4

Crest Factor Function

The Crest Factor function simulates the current waveform of a capacitive input
rectified load.
Fig.3-6 shows the front panel display of the crest factor setting. The input terminal
measurements are displayed on the upper side.

Fig.3-6

Crest Factor Setting Display

If the LED above the LOAD key is on, press the LOAD key to change to
load-off.

Press the I SET key to enable CC mode.

The C.C LED at the top of the panel illuminates.

Press the SHIFT + C.F key to enable the crest factor function.

The LED above the C.F key illuminates.

Pressing the C.F key again allows the crest factor setting to be
specified (the existing setting appears in the lower part of the display).

"CREST FACTOR" appears in the lower part of the display.

Use the rotary knob to set the crest factor. (The crest factor is set to 2.0
in this example.)

0.00Ar 0.0Ap 95.1V
--CREST FACTOR 1.4--

RMS current value

Peak current value

RMS voltage value

Crest factor

0.00Ar 0.0Ap 95.1V
-- ISET 7.00A --

0.00Ar 0.0Ap 95.1V
--CREST FACTOR 1.4--

0.00Ar 0.0Ap 95.1V
--CREST FACTOR 2.0--

Содержание PCZ1000A





































































































Результаты поиска

Содержание PCZ1000A

Отзывы:

Похожие инструкции для PCZ1000A

Бренды по названию

Популярные бренды

Kikusui PCZ1000A, Руководство по эксплуатации

Результаты поиска

Содержание PCZ1000A

Отзывы:

Похожие инструкции для PCZ1000A

Бренды по названию

Популярные бренды