Keba KeContact Series Скачать руководство пользователя страница 20

Страница: 20 / 156

Hardware installation

20 / 156

4.5 DIP-switch settings

Changes in the DIP-switch settings will take effect once the charging station has been restarted!
To do this, press the

[Service button]

for

1 second

or switch the power supply off/on.

DIP-switches

DIP-switches

The DIP-switches are used for the addressing and con-
figuring the charging station and are located under the
connector panel cover.

[DSW1]

…configuration (upper DIP-switch)

[DSW2]

…addressing (lower DIP-switch)

DIP-switch example

The figure shows for a better explanation, the position
of the DIP-switches for the ON and OFF state.

INPUT/OUTPUT (DSW1) / ONLY FOR STANDARD MODE

Function

DIP-switch

Figure

External enable input [X1]

is used

D1.1

ON=yes

Switch contact output [X2]

is used

D1.2

ON=yes

SmartHome interface via UDP
(details see “UDP Program-
mers Guide”)

D1.3

ON=

enabled

Содержание KeContact Series





























































































































































Результаты поиска

Содержание KeContact Series

Отзывы:

Похожие инструкции для KeContact Series

Бренды по названию

Популярные бренды

Keba KeContact Series, Системное руководство

Результаты поиска

Содержание KeContact Series

Отзывы:

Похожие инструкции для KeContact Series

Бренды по названию

Популярные бренды