KAESER TG 450 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 116

KAESER TG 450 Скачать руководство пользователя страница 69

10 Maintenance

10.1 Ensuring safety

Follow these instructions for to ensure safe machine maintenance.
Warning instructions are given prior to a potentially dangerous task.

Disregarding warning instructions can result in life-threatening injuries!

Observe safety instructions

Ignoring safety instructions can cause unforeseeable dangers!
➤ Follow the instructions in chapter 3 "Safety and Responsibility".
➤ Allow maintenance work to be performed by authorized personnel only!
➤ Make sure that no personnel are working on the machine.
➤ Ensure that all service doors and panels are locked.

When working on live components

Touching live components can result in electric shocks, burns or death.
➤ Work on electrical equipment may only be carried out by authorized electricians.
➤ Switch off the power supply disconnecting device, lock out/tag out the device, verify the ab‐

sence of any voltage.

➤ Check that there is no voltage on potential-free contacts.
➤ Before starting work on the control cabinet or the fan, wait at least 5 minutes after the power

supply disconnecting device has been switched off.

Working on the compressed air system

Compressed air is contained energy. Uncontrolled release of this energy can cause serious injury

or death. The following safety instructions relate to any work on components that could be under

pressure.
➤ Close shut-off valves or otherwise isolate the machine from the compressed air system to en‐

sure that no compressed air can flow back into the machine.

➤ Vent all pressurized components and enclosures.
➤ Do not open or dismantle any valves.

Working on the drive system

Touching live components can result in electric shocks, burns or death.

Touching the fan wheel whilst the machine is switched on can result in serious injury.
➤ Switch off the power supply disconnecting device, lock out/tag out the device, verify the ab‐

sence of any voltage.

➤ Do not open the enclosure while the machine is switched on.

Further information Information regarding authorized personnel can be found in chapter 3.4.2.

Information regarding dangers and their avoidance can be found in chapter 3.5.

10 Maintenance

10.1 Ensuring safety

No.: 901760 02 USE

Operator Manual Refrigerated Dryer
TG

59

«
...
67
68
69
70
71
...
»

Содержание TG 450





















































































































Отзывы:

Нет отзывов