KAESER TG 450 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 116

KAESER TG 450 Скачать руководство пользователя страница 30

3.8 Emergency situations

3.8.1 Correct fire fighting

Suitable measures

Calm and prudent action can safe lives in the event of a fire.
➤ Keep calm.
➤ Give the alarm.
➤ Shut off supply lines if possible.

Power supply disconnecting device (all phases)

Cooling water (if present)

➤ Warn and move endangered personnel to safety.
➤ Help incapacitated persons.
➤ Close the doors.
➤ When trained accordingly: Attempt to extinguish the fire.

Extinguishing substances

➤ Suitable extinguishing media:

Foam

Carbon dioxide

Sand or soil

➤ Unsuitable extinguishing media:

Strong jet of water

3.8.2 Treating injuries from handling refrigerant

Eye contact:

Severe eye irritation, watering, reddening, and swelling of the eyelids.

Risk of caustic burns and frostbite.
➤ Open eyelids wide to allow product to evaporate.
➤ Hold the eyelid wide and rinse the eye with running water.
➤ Consult an ophthalmologist if you experience lasting pains.

Skin contact:

Initially a sensation of chill, skin may redden subsequently.

Risk of frostbite.
➤ Allow the product to evaporate.
➤ Rinse with lukewarm water.
➤ Consult a physician if experiencing lasting pain or reddened skin.

Inhalation:

At high concentrations, risk of cardiac irregularity (arrhythmia).

At very high concentration, risk of asphyxia caused by oxygen deficiency.
➤ Remove victim to the fresh air.

3

Safety and Responsibility

3.8

Emergency situations

20

Operator Manual Refrigerated Dryer
TG

No.: 901760 02 USE

«
...
28
29
30
31
32
...
»

Содержание TG 450





















































































































Отзывы:

Нет отзывов