KAESER TG 450 Скачать руководство пользователя страница 67

Страница: 67 / 116

Fig. 30 Displays and connections of the communications module

Item Display

Fault

Possible cause

Measure

COM

LED

flashes

red 1x/s

CAN communi‐

cation faulty

SCS without voltage

Check the power supply

Communications module

loose

Plug in the communica‐

tions module and tighten

the fastening screws

flashes

red 2x/s

Ethernet com‐

munication faul‐

See the following faults

ETH

LINK

off

No Ethernet

connection

Network connection is in‐

terrupted

Check network cable and

plug

ETH

ACT

off

Communications module

at the bus master incor‐

rectly parametrized or not

at all

Parametrize the module

at the master, see chapter

7.4.1

Incorrect IP address or

communication settings

Reset to factory setting

and re-register at the bus,

see chapter 7.4.1

ETH

LINK

on, green No Ethernet

communication

SIGMA AIR MANAGER

4.0 out of operation

Switch on SIGMA AIR

MANAGER 4.0

ETH

ACT

off

Ethernet network out of

operation

Contact IT personnel

Tab. 35 Fault messages on the communications module

Fault Recognition and Rectification

9.3

Communications module – Troubleshooting

No.: 901760 02 USE

Operator Manual Refrigerated Dryer
TG

Содержание TG 450





















































































































Результаты поиска

Содержание TG 450

Отзывы:

KAESER TG 450, Руководство оператора, Страница: 67 / 116

Результаты поиска

Содержание TG 450

Отзывы: