Julabo Presto Series Скачать руководство пользователя страница 62

Страница: 62 / 121

"Connect unit" menu

2.13.2018

Network-based connection

Obtain IP via DHCP

>true<

If you would like to connect the

to your network and

your network has a DHCP server, then the

will be

automatically assigned an IP address.

To enable this, set the item

Obtain IP via DHCP

>true<

Connect the

's network socket to a socket in your

network. The

will be automatically detected in the

network and the DHCP server will issue an IP address. A few

seconds later, this IP address will appear in the

menu.

Obtain IP via DHCP
>false<

You can also assign a fixed IP address to the

To do this, set the item

Obtain IP via DHCP

>false<

and

manually enter into the

's Ethernet menu the IP

address, subnet mask, and, if required, the default gateway.

Attention:

Most networks have certain address ranges that are reserved for

the issuance of fixed IP addresses. Please contact a network

administrator before changing the settings on the

Remark:

When manually setting network parameters, you must always enter

both the IP address and the subnet mask. The settings will be

shown in the display only after both parameters have been

entered!

Modbus-Port page 102

Содержание Presto Series


























































































































Результаты поиска

Содержание Presto Series

Отзывы:

Julabo Presto Series, Руководство по эксплуатации, Страница: 62 / 121

Результаты поиска

Содержание Presto Series

Отзывы: