Julabo Presto Series Скачать руководство пользователя страница 109

Страница: 109 / 121

USER INTERFACE

2.13.2018

109

15.1.

Alarm messages

Alarm-Code

Cause

Diagnosis / Remedy

E01

Fluid level is too low.

The unit is operating with too less or without

temperature control liquid. Please refill the

temperature control liquid. Then turn off the

unit at the power switch, wait 4 seconds,

and turn the unit back on.

E05

The line to an internal temperature sensor is

interrupted.

If this error continues to occur, please

contact JULABO Service.

E06

Local overheating at heater.

(1) The viscosity of the liquid may not

exceed the maximum permitted value at any

working temperature.

(2) The medium has not been completely

purged.

(3) There is too less recirculation.

E14

The temperature is above the high

temperature cut-off temperature setting.

Please check the high temperature cut-off

setting and increase the setting if

necessary.

WARNING: When adjusting the safety

temperature, please note the operating

limits (combustion point) of the temperature

control liquid used. Ask the manufacturer of

the temperature control liquid for

information.

E15

Short circuit or interrupt in external control

probe.

The unit is configured for external control

but the line to the external control probe

(EXT Pt100) is short circuit or interrupted.

Check the electrical connection to the

external control probe.

E33

The line to an internal temperature sensor is

short-circuited or interrupted.

If this error continues to occur, please

contact JULABO Service.

E38

Error on the external Pt100 probe with a

setpoint set

Setpoint on external Pt100 is set, but

there is no signal.

Please check whether an external Pt100

probe is connected, or adjust the

setpoint.

E60

FRAM write/read error

Turn off the unit at the power switch, wait 4

seconds, and turn the unit back on.

Содержание Presto Series


























































































































Результаты поиска

Содержание Presto Series

Отзывы:

Julabo Presto Series, Руководство по эксплуатации, Страница: 109 / 121

Результаты поиска

Содержание Presto Series

Отзывы: