Julabo Presto Series Скачать руководство пользователя страница 113

Страница: 113 / 121

USER INTERFACE

2.13.2018

113

Alarm-Code

Cause

Diagnosis / Remedy

E427

Error in Stage 1 of the cooling system.

One or more of the following problems has

occurred:

(1) Ambient temperature too high

(2) Condenser contaminated

(3) Cooling water temperature too high

(4) Quantity of cooling water too low

E428

Error in stage 1 of the cooling system.

One or more of the following problems has

occurred:

(1) Ambient temperature too high

(2) Condenser contaminated

(3) Cooling water temperature too high

(4) Quantity of cooling water too low

E429

Smoke detection alarm

Identify cause and start firefighting

measures.

E430

Error in stage 1 of the cooling system.

One or more of the following problems has

occurred:

(1) Ambient temperature too high

(2) Condenser contaminated

(3) Cooling water temperature too high

(4) Quantity of cooling water too low

E431

No current draw detected from the

compressor / compressor defective

If this error continues to occur, please

contact JULABO Service.

E432

Error in cooling system.

If the problem persists, please contact

JULABO service.

E433

Error in cooling system.

If the problem persists, please contact

JULABO service.

E434

Cooling water temperature out of

specifications.

Check cooling water.

E435

Cooling water temperature out of

specifications.

Check cooling water.

E502

Error in communications with the

WirelessTEMP USB stick for remote

control.

The WirelessTEMP USB stick has been

deactivated. Please reconnect the

WirelessTEMP USB stick or switch the

remote control.

E503

External setpoint assigned through

Eprog, but no analog module found

Please deactivate external setpoint

assignment through Eprog, or connect

an analog module.

E504

External setpoint assigned through

Eprog, but no analog module found

Please deactivate external setpoint

assignment through Eprog, or connect

an analog module.

E505

Invalid setpoint with setpoint assignment

through Eprog.

The analog module is sending an invalid

setpoint. Please check the Eprog

settings.

Содержание Presto Series


























































































































Результаты поиска

Содержание Presto Series

Отзывы:

Julabo Presto Series, Руководство по эксплуатации, Страница: 113 / 121

Результаты поиска

Содержание Presto Series

Отзывы: