Julabo Presto Series Скачать руководство пользователя страница 31

Страница: 31 / 121

USER INTERFACE

2.13.2018

Notice

Settings of setpoint limits for
>

Pumpstage

< and

Limit Pressure

< are active.

Examples:



If the >Limit Pressure< is exceeded at >stage 3< an alarm including

the cut-off of the unit is activated!

5.2.1.2.

Type „Pressure control“

Select .

Set pressure setpoint.

Example „0.5“

Setpoint limits

refer to page 48

The setting ranges depend on the performance category of the

temperature control system.

Example: see display of unit.





Settings in the >

" Adjust safety " menu

< will influence these

values. If a >

Setpoint limit

< is set, you will not be able to

exceed or fall below this value, respectively.
You will receive a message stating "Value is too small or too
large"

Example:

The displayed value, in this case „Max:0.65“, always refers to
the next higher limit.

Содержание Presto Series


























































































































Результаты поиска

Содержание Presto Series

Отзывы:

Julabo Presto Series, Руководство по эксплуатации, Страница: 31 / 121

Результаты поиска

Содержание Presto Series

Отзывы: