Julabo Presto Series Скачать руководство пользователя страница 26

Страница: 26 / 121

"Determine thermodynamics" menu

2.13.2018

A Standard

B Aperiodic

C Temperature stability
D Setpoint

E Temperature ramp

Dynamic <

This parameter influences the temperature sequence only
during

internal

control.

Available parameters:

Standard

The temperature will climb faster, but may overshoot

by up to 5%. If a ramp is defined, the temperature sequence
will largely follow this ramp.

Aperiodic

Temperature will increase with time offset (no

overshoots).

Both settings will achieve adequate temperature stability after
approximately the same amount of time.

Setting range: 0.00 to 5.00

Setpoint

Ext External temperature
Int

Internal temperature

>CoSpeed factor<

This parameter will influence the temperature sequence only
with

external

control.

The setting influences calculation of the control parameters
during identification, thereby influencing control behavior.

Содержание Presto Series


























































































































Результаты поиска

Содержание Presto Series

Отзывы:

Julabo Presto Series, Руководство по эксплуатации, Страница: 26 / 121

Результаты поиска

Содержание Presto Series

Отзывы: