Julabo Presto Series Скачать руководство пользователя страница 28

Страница: 28 / 121

"Determine thermodynamics" menu

2.13.2018

5.1.4. "Adjust limits" menu

Select menu

The buttons will display the current
settings.



Example: setting ranges see
display of unit.



The >Limits< menu allows you to define the minimum and

maximum values for all important setting ranges and power

variables.
The setting ranges depend on the performance category of the

temperature control system.

Selected maximum heating / cooling capacity

The unit's heating and cooling capacities are adjustable.

100% corresponds to the capacity specified in the technical

data.

Setting range:

Max. heating capacity 0 to 100% in 1% steps

Max. cooling capacity 0 to 100% in 1% steps

Min. internal temp

and

max. internal temp

Maximum and minimum setpoint in internal bath.
The max. internal temp and min. internal temp limits apply only

when using the "external" operating mode. Max. internal temp and

min. internal temp define static limits for the anticipated

temperatures in the internal bath. The temperature controller

cannot exceed these limits, even if this would be necessary in

order to achieve the desired temperature in the external system. In

some situations this may prevent you from reaching the external

setpoint.

Reasons for setting limits:



Protect the heat transfer liquid from overheating.



Prevent the high temperature cut-off >Error 14< from
triggering an undesired alarm shutoff.
Set the >

Internal max

value at least 5 °C below the

>High temperature cut-off (tank)< value.



Protect the pump motor from excessive viscosity of the
heat transfer liquid at low temperatures.

Содержание Presto Series


























































































































Результаты поиска

Содержание Presto Series

Отзывы:

Julabo Presto Series, Руководство по эксплуатации, Страница: 28 / 121

Результаты поиска

Содержание Presto Series

Отзывы: