Julabo Presto Series Скачать руководство пользователя страница 60

Страница: 60 / 121

"Connect unit" menu

2.13.2018

Subnet mask

Example: 255.255.240.0

The subnet mask is a bit mask that indicates which part of the

IP address represents the network and which part

represents the device.

If a bit is set to "1" in the subnet mask, the corresponding bit

belongs to the subnet mask; otherwise, it belongs to the device

address.

In the example, the part 10.3.3.236 of the IP address would define

the subnet and the last part 2 would define the device address.

The final byte of the subnet mask can be set so that it belongs

partially to the subnet and partially to the device address. For

example, a subnet mask of 255.255.240.0 would mean that the

first two bytes belong completely to the IP address and from the

third byte the first 4 bits belong to the subnet. In this case, the

device address would consist of the last 4 bits of the third byte and

the entire fourth byte.

Remark:

The subnet part and the device part may not be mixed with each

other. For example, a subnet mask of 255.240.255.0 is not

permitted.

Default Gateway

Example.:10.3.15.254

The default gateway serves as the communications interface

between your own network and other networks.

If you wish to communicate with a PC that is not located in the

same network as the

(subnet mask), this

communication will always pass through the gateway.

Remote display:

The remote display allows you to remotely control the

using a PC.

At the

, switch the

Remote Display

menu item to

active

and start the

program on your PC. Then click on

File



Connect

. A dialog window will appear that lists all of the devices

found in the network.



It may take a few seconds before all devices in the network

are found and added to the list. Please wait until your device is

displayed.

When you click on one of the

in the list, that unit's IP

address will appear in the lower field of the window. Please

compare the IP address of the selected

with the

settings in the

Ethernet menu

of the

you wish to

control remotely.



When

Remote display

active

, the letter

will be added to the

icon in the main window. This does not mean that remote control

via ethernet is activated.

Содержание Presto Series


























































































































Результаты поиска

Содержание Presto Series

Отзывы:

Julabo Presto Series, Руководство по эксплуатации, Страница: 60 / 121

Результаты поиска

Содержание Presto Series

Отзывы: