janitza UMG 509 Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 124

background image

73

UMG 509

Password

The user can block access to the configuration with a
password. The configuration can then only be changed
directly on the device by entering the password.

The password consists of a 6-digit code.

Setting range:

1-999999 = With password

000000 = Without password

Password (000000) is not factory-programmed.

• To change a password that has already been set,

you must know the current password.

• Note down the changed password.
• When selecting the "Password" (green marking),

the password can be changed using the 6 key
(enter) and keys 2 to 5. Pressing the 6 key again
confirms the entry.

• If you no longer want a password prompt, enter

the password "000000".

C

Forgot password

If you no longer remember your password,
you can only delete it using the "GridVis"
PC software.
In order to do so, connect the UMG 509
to the PC with a suitable interface. More
information can be found in the GridVis
assistant.

«
...
71
72
73
74
75
...
»

Содержание UMG 509





























































































































Отзывы:

Нет отзывов

Похожие инструкции для UMG 509

Бренд: UEi Страницы: 4

Бренд: Parr Instrument Страницы: 110

DigitalFlow XMT868i

Бренд: Panametrics Страницы: 74

Бренд: Kawai Страницы: 142

Бренд: Kawai Страницы: 10

Бренд: C-LOGIC Страницы: 4

Бренд: ICT Страницы: 48

Бренд: OfiTE Страницы: 67

Бренд: Bacharach Страницы: 28

Бренд: Keithley Страницы: 32

Ultraprobe 9000

Бренд: UE Systems Страницы: 25

ULTRAPROBE 10000

Бренд: UE Systems Страницы: 6

Бренд: WAGNER Страницы: 9

Бренд: VELOCICALC Страницы: 10

Бренд: ICS Schneider Messtechnik Страницы: 40

Бренд: ASCEL Electronic Страницы: 64

Бренд: iSTEK Страницы: 15

Бренд: doble Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды