janitza UMG 509 Скачать руководство пользователя страница 55

Страница: 55 / 124

UMG 509

Configuration

The supply voltage must be connected for
the configuration of the UMG 509.

Connecting the supply voltage

• The supply voltage level for the UMG 509 is specified

on the rating plate.

• After connecting the supply voltage, a start display

appears. Approximately ten seconds later, the UMG
509 switches to the first "Home" measured value
display.

• If no display appears, check whether the applied

supply voltage is within the rated voltage range.

Please note!

If the supply voltage does not correspond
to the voltage indicated on the rating
plate, this may lead to malfunctions
and severe damage to the device.

Fig. Example of the "Home" measured
value display

Содержание UMG 509





























































































































Результаты поиска

Содержание UMG 509

Отзывы:

Похожие инструкции для UMG 509

Бренды по названию

Популярные бренды

janitza UMG 509, Руководство по эксплуатации и технические данные

Результаты поиска

Содержание UMG 509

Отзывы:

Похожие инструкции для UMG 509

Бренды по названию

Популярные бренды