janitza UMG 509 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 124

background image

11

UMG 509

Measuring process

The UMG 509 measures continuously and calculates
all effective values over a 200 ms interval. The device
measures the real effective value (TRMS) of the voltages
and currents connected to the measurement inputs.

Operating concept

You can program and call up the measured values via
many routes using the UMG 509.

• Directly

on the device via 6 buttons and the display

• Using the

GridVis

programming software.

• Using the device

homepage

• Using the Modbus

protocol

.

You can modify and call up the data using the
Modbus address list. The list can be called up via
the device's home page and can be found on the
enclosed CD.

This operation manual only describes how to operate the
UMG 509 using the buttons.
The GridVis programming software has its own "online
help" system.

GridVis network analysis software

The UMG 509 can be programmed and read out using the
GridVis network analysis software included in the scope
of the delivery. For this, a PC must be connected
to the UMG 509 via a serial interface (RS485/Ethernet).

GridVis features

•  Programming the UMG 509
•  Configuring recordings
•  Analysing the read out data according to

EN 61000-2-4.

•  Reading out recordings
•  Saving data to a database
•  Graphical representation of measured values
•  Programming customer-specific applications

«
...
9
10
11
12
13
...
»

Содержание UMG 509





























































































































Отзывы:

Нет отзывов

Похожие инструкции для UMG 509

Бренд: Larson Davis Страницы: 193

Бренд: Facom Страницы: 116

Бренд: ICM Controls Страницы: 8

Бренд: jenway Страницы: 18

Бренд: Sanmenxia Страницы: 17

Бренд: SANKO Страницы: 25

Бренд: Samson Страницы: 2

Бренд: Yamaha Страницы: 120

Бренд: Yamaha Страницы: 110

Portatone PSR-5700

Бренд: Yamaha Страницы: 79

Бренд: Yamaha Страницы: 112

Бренд: Yamaha Страницы: 82

Бренд: Yamaha Страницы: 108

Бренд: Victron energy Страницы: 46

Бренд: Ramsey Electronics Страницы: 40

Бренд: E Instruments Страницы: 2

Бренд: Suaoki Страницы: 79

Бренд: Ofs Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды