janitza UMG 509 Скачать руководство пользователя страница 68

Страница: 68 / 124

UMG 509

Events

Events are threshold value violations of set threshold
values for current and voltage.

Here, threshold values are compared with the full-
wave effective values for current and voltage from
the measurement channels. The event record consists
of a mean value, a minimum or maximum value, a start
time and an end time.

Fig. Shows the full wave effective values for an event.

• Monitoring of the threshold values can be switched

off (Off/Manual).

• Threshold values must be set as a percentage

of the nominal value.

• Threshold values can be set for excess voltage,

undervoltage and overcurrent.

• If an event has occurred, the corresponding measured

value is recorded with the set pre-run and after-run
periods (respectively 0..1000 full waves).

• Event records are configured with the GridVis

and displayed with the event browser.

Limit value

Measured

value

Vollwellen-

effektivwert

Limit value

violations

before the

lead time

End time

Limit value violations

before the follow-up time

Event

Follow-up time

Lead time

Start time event

(Trigger time)

Event record

Pre-run

After-run

• An event describes a fault due to undervoltages/

overvoltages, voltage loss, overcurrent, overfrequency/
underfrequency and rapid frequency changes

• An event is triggered if there is an uninterrupted

threshold value violation within the lead time.
The event is ended if there is no threshold value
violation within the after-run time.

Содержание UMG 509





























































































































Результаты поиска

Содержание UMG 509

Отзывы:

Похожие инструкции для UMG 509

Бренды по названию

Популярные бренды

janitza UMG 509, Руководство по эксплуатации и технические данные

Результаты поиска

Содержание UMG 509

Отзывы:

Похожие инструкции для UMG 509

Бренды по названию

Популярные бренды