janitza UMG 509 Скачать руководство пользователя страница 26

Страница: 26 / 124

UMG 509

Supporting measurement, input V4

Fig. Measurement in a three-phase 4-conductor
network with symmetric loading.

Fig. Measurement in a three-phase 3-conductor
network with symmetric loading.

Fig. Measurement of the voltage between N and PE.
Measurement of the current in the neutral conductor.

If the baseline measurement (inputs V1-V3)
is connected to a three-phase 3-conductor
network, the supporting measurement
(input V4) can no longer be used as
a measurement input.

For measurement with the supporting
measurement (V4), a voltage must be
connected to the baseline measurement
for frequency determination.

L1
L2
L3

4w 1m

S1 S2

L1
L2
L3

3w 1m

S1 S2

2w 1n

S1 S2

L1
L2
L3

4w 1m

S1 S2

L1
L2
L3

3w 1m

S1 S2

2w 1n

S1 S2

L1
L2
L3

4w 1m

S1 S2

L1
L2
L3

3w 1m

S1 S2

2w 1n

S1 S2

Measured voltages and measured currents
must derive from the same network.

Содержание UMG 509





























































































































Результаты поиска

Содержание UMG 509

Отзывы:

janitza UMG 509, Руководство по эксплуатации и технические данные, Страница: 26 / 124

Результаты поиска

Содержание UMG 509

Отзывы: