janitza UMG 509 Скачать руководство пользователя страница 67

Страница: 67 / 124

UMG 509

Mode (absolute)

If a sampled value exceeds the set threshold value,
a transient is detected.

• Off

- Transient monitoring has been switched off.

• Automatic

- Factory default setting.

The threshold value is calculated automatically
and is 110% of the current 200 ms effective value.

• Manual

- The transient monitoring uses the

configurable threshold values under "Peak U".

Mode (delta)

If the difference between two neighbouring sampled
points exceeds the set threshold value, a transient
is detected.

• Off

- Transient monitoring has been switched off.

• Automatic

- Factory default setting. The threshold

value is calculated automatically and is 0.2175
times the current 200ms effective value.

• Manual

- The transient monitoring uses the

configurable threshold values under "Trns U".

Adopt L2-L4

The transient monitoring can be adjusted for each
phase. You can adopt these settings from phase L1 and
apply them to phases L2, L3 and L4.

• No

- The settings from phase L1 will not be applied

to phases L2, L3 and L4

• Yes

- The settings from phase L1 will be applied

to phases L2, L3 and L4

Содержание UMG 509





























































































































Результаты поиска

Содержание UMG 509

Отзывы:

janitza UMG 509, Руководство по эксплуатации и технические данные, Страница: 67 / 124

Результаты поиска

Содержание UMG 509

Отзывы: