janitza UMG 509 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 124

janitza UMG 509 Скачать руководство пользователя страница 53

53

UMG 509

Transients list

The detected transients are listed in the transients list.
• The transients list consists of 2 pages.
• On page 1, the transients 1 through 8 are listed and

on page 2, the transients 9 through 16 are listed.

Displaying transients

• Using the 2 and 5 keys, scroll to the "Transient" main

value display.

• Select the desired page using

the 4 key.

• Navigate to the transients list using key 6 (select)

and select a transient using the 3 or 4 keys.

• Using the 6 key (select), have a transient displayed in

a graph.

• Show or hide the legend using the 6 key (select).
• You can exit the transient graph display using

the 1 key (ESC).

Transient voltages are fast impulse transient
effects in electrical networks.
The time when transient voltages occur cannot
be predicted and they have a limited duration.
Transient voltages are caused by lightning strikes,
switching operations or by tripped fuses.

«
...
51
52
53
54
55
...
»

Содержание UMG 509





























































































































Отзывы:

Нет отзывов