janitza UMG 509 Скачать руководство пользователя страница 99

Страница: 99 / 124

UMG 509

Pulse value

The pulse value is used to indicate how much power
(Wh or varh) should correspond to a pulse.
The pulse value is determined by the maximum
connected load and the maximum number of pulses per
hour.

If you check the pulse value with a positive sign,
the pulses will only be emitted when the measured value
has a positive sign.

If you check the pulse value with a negative sign,
the pulses will only be produced when the measured
value has a negative sign.

Since the reactive power meter operates
with a backstop, pulses will only
be generated with inductive load applied.

Since the effective power meter operates
with a backstop, pulses will only
be generated when drawing electricity.

Pulse value =

max. connected load

max. number of pulses/h

[Pulse/Wh]

Содержание UMG 509





























































































































Результаты поиска

Содержание UMG 509

Отзывы:

Похожие инструкции для UMG 509

Бренды по названию

Популярные бренды

janitza UMG 509, Руководство по эксплуатации и технические данные

Результаты поиска

Содержание UMG 509

Отзывы:

Похожие инструкции для UMG 509

Бренды по названию

Популярные бренды