janitza UMG 509 Скачать руководство пользователя страница 115

Страница: 115 / 124

115

UMG 509

THD of the voltage

THDu

1.0 (IEC61557-12)

up to 2.5 kHz

0% to 999 %

THD of the voltage

THD-Ru

1.0 (IEC61557-12)

up to 2.5 kHz

0% to 999 %

Current harmonics

Cl. 1

(IEC61000-4-7)

up to 2.5 kHz

0 A to 9999 kA

THD of the current

THDi

1.0 (IEC61557-12)

up to 2.5 kHz

0% to 999 %

THD of the current

THD-Ri

1.0 (IEC61557-12)

up to 2.5 kHz

0% to 999 %

Mains signal voltage (interharmonics
voltage)

MSV

- -

Declarations
1)  In relation to the amplitude.
2)  In relation to phase and amplitude.
3)  In relation to fundamental oscillation.
4)  In relation to effective value.
5)  Precision class 0.2 with.../ 5A converter.

Precision class 0.5 with.../ 1A converter.

* The display returns to 0 W once the max.

total working value range has been reached.

6) Calculation from fundamental oscillation.
7) Precision class 0.5S per IEC62053-22

Содержание UMG 509





























































































































Результаты поиска

Содержание UMG 509

Отзывы:

Похожие инструкции для UMG 509

Бренды по названию

Популярные бренды

janitza UMG 509, Руководство по эксплуатации и технические данные

Результаты поиска

Содержание UMG 509

Отзывы:

Похожие инструкции для UMG 509

Бренды по названию

Популярные бренды