janitza UMG 509 Скачать руководство пользователя страница 57

Страница: 57 / 124

UMG 509

Communication

The UMG 509 has an Ethernet and a RS485 interface.

Ethernet (TCP/IP)

Select the type of the address assignment for
the Ethernet interface here.

DHCP mode

• Off

- The IP address, netmask and gateway are

defined by the user and set directly on the UMG 509.
Select this mode for straightforward networks without
DHCP servers.

• BOOTP -

BootP enables the fully automatic

integration of a UMG 509 into an existing network.
However, BootP is an older protocol and does not
provide the scope of functions provided by DHCP.

• DHCP

- When started, the UMG 509 automatically

obtains the IP address, the network mask and
the gateway from a DHCP server.

Factory default setting:

DHCP

Connection of the UMG 509 to the
Ethernet may only be carried out after
consulting the network administrator!

Содержание UMG 509





























































































































Результаты поиска

Содержание UMG 509

Отзывы:

janitza UMG 509, Руководство по эксплуатации и технические данные, Страница: 57 / 124

Результаты поиска

Содержание UMG 509

Отзывы: