janitza UMG 509 Скачать руководство пользователя страница 16

Страница: 16 / 124

UMG 509

Installation

Ground wire connection

Use a ring cable lug for connecting the protective
conductor to the UMG 509.

Supply voltage

The UMG 509 needs supply voltage to operate. The type
and amount of the supply voltage required is specified
on the rating plate. The supply voltage is connected
on the rear side of the device via terminal blocks.

Before connecting the supply voltage, ensure that
the voltage and frequency correspond to the details
on the rating plate!

The supply voltage must be connected through a UL/IEC
approved fuse (6A type C).

Caution: Risk to life!

The ground wire connection on the device
must be connected with the system
earthing.

Fig. connection example of the supply voltage
to a UMG 509.

Circuit breaker

Fuse

N PE

Protective conductor

Connection point of

the protective conductor

Содержание UMG 509





























































































































Результаты поиска

Содержание UMG 509

Отзывы:

Похожие инструкции для UMG 509

Бренды по названию

Популярные бренды

janitza UMG 509, Руководство по эксплуатации и технические данные

Результаты поиска

Содержание UMG 509

Отзывы:

Похожие инструкции для UMG 509

Бренды по названию

Популярные бренды