janitza UMG 509 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 124

background image

56

UMG 509

Configuration menu

After the power returns, the device starts on the "Home"
measured value display.

• Open the Configuration menu using the 1 button.

If you are in a measured value display for main values,
you can navigate directly to the "Home" measured
value display using the 1 button (home). Pressing the 1
key again opens the Configuration menu. Using the 3
or 4 keys, you select the desired submenu that can be
activated using the 6 key (enter).

Language

You can set the language for the measured value displays
and menus directly in the "Configuration" menu.

There are different languages available for selection.
The factory default setting for the language is "English".

If the language field is marked green, then the desired
language can be selected by pressing the key 6 (enter)
and the keys 3 or 4. Pressing the key 6 (enter) again
confirms the selection and changes the language.

«
...
54
55
56
57
58
...
»

Содержание UMG 509





























































































































Отзывы:

Нет отзывов

Похожие инструкции для UMG 509

Бренд: ABQ Industrial Страницы: 15

Бренд: ABQINDUSTRIAL Страницы: 3

Бренд: Cannon Страницы: 64

Бренд: Cannon Страницы: 73

Бренд: Radio Shack Страницы: 44

Бренд: Radiodetection Страницы: 2

Бренд: Keeler Страницы: 68

Vigilantplant NFBU200-S Series

Бренд: YOKOGAWA Страницы: 24

Бренд: horiba Страницы: 117

Бренд: Sequid Страницы: 111

LaserHybrid SB 360i

Бренд: Fronius Страницы: 104

PLUS 3631 Series

Бренд: insize Страницы: 1

Бренд: Datakom Страницы: 28

Бренд: Gallagher Страницы: 20

LAQUAtwin-Na-11

Бренд: horiba Страницы: 5

Бренд: Omicron Страницы: 76

Бренд: Galileo Страницы: 30

CR-2010 PRO Series

Бренд: G-Tek Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды