janitza UMG 509 Скачать руководство пользователя страница 83

Страница: 83 / 124

UMG 509

Frequency measurement

The UMG 509 requires the mains frequency for
the measurement. The mains frequency can be defined
by the user or automatically determined by the device.

• For the UMG 509 to automatically determine

the frequency, a voltage (V-Vref) greater than 10Veff
must be applied to at least one of the voltage
measurement inputs.

• The mains frequency must be in the range from

40Hz to 70Hz.

• If there is no sufficiently high measured voltage

available, the UMG 509 cannot determine
the mains frequency and thus cannot perform any
measurements.

Direction of the rotating field

Check the direction of the rotating field voltage
in the measured value display of the UMG 509.

A “right” rotation field usually exists.

Presentation of the phase sequence according
to the direction of the rotating field.

UL1-UL2-UL3 = right rotation field
UL1-UL3-UL2 = left rotation field

Содержание UMG 509





























































































































Результаты поиска

Содержание UMG 509

Отзывы:

Похожие инструкции для UMG 509

Бренды по названию

Популярные бренды

janitza UMG 509, Руководство по эксплуатации и технические данные

Результаты поиска

Содержание UMG 509

Отзывы:

Похожие инструкции для UMG 509

Бренды по названию

Популярные бренды