janitza UMG 509 Скачать руководство пользователя страница 52

Страница: 52 / 124

UMG 509

Deleting min./max. values individually

• Using the 2 and 5 keys, scroll to the desired measured

value display.

• Activate the measured value selection using the 6 key

(select).

• The background colours for the measured value

switches from grey to green. The additional information
is displayed in blue window.

• Using the 2 and 5 keys, select the desired minimum

or maximum value.

• The time along with the date and time of the occurrence

are displayed as additional information.

• Using the 6 key (reset), you can delete the selected

minimum or maximum value.

• End the procedure using the 1 key (ESC) or select

another minimum or maximum value with the 2 to 5
keys.

The date and time for the minimum/
maximum values are specified displayed
in UTC time (Coordinated Universal Time).

Содержание UMG 509





























































































































Результаты поиска

Содержание UMG 509

Отзывы:

Похожие инструкции для UMG 509

Бренды по названию

Популярные бренды

janitza UMG 509, Руководство по эксплуатации и технические данные

Результаты поиска

Содержание UMG 509

Отзывы:

Похожие инструкции для UMG 509

Бренды по названию

Популярные бренды