janitza UMG 509 Скачать руководство пользователя страница 82

Страница: 82 / 124

UMG 509

Connecting the measured voltage

• Voltage measurements above the nominal mains

voltages listed must be excluded by means
of a voltage transformer!

• After connecting the measured voltages,

the measured values displayed by the UMG 509
for the L-N and L-L voltages must correspond
to those at the voltage measurement input.

• If a voltage transformer factor is programmed,

it must be taken into consideration for
the comparison.

Commissioning the unit

Connecting the supply voltage

• The supply voltage level for the UMG 509

is specified on the rating plate.

• After connecting the supply voltage, a display

appears. Approximately 15 seconds later,
the UMG 509 switches to the first measured value
display.

• If no display appears, check whether the power

supply voltage is within the rated voltage range.

Please note!

If the supply voltage does not correspond
to the voltage indicated on the rating
plate, this may lead to malfunctions
and severe damage to the device.

Please note!

The UMG 509 is only suitable for
use in networks where overvoltages
of overvoltage category 600V CATIII can
occur.

Please note!

The UMG 509 is not suitable for
measuring DC voltages.

Содержание UMG 509





























































































































Результаты поиска

Содержание UMG 509

Отзывы:

janitza UMG 509, Руководство по эксплуатации и технические данные, Страница: 82 / 124

Результаты поиска

Содержание UMG 509

Отзывы: