ITW Orbitalum ORBIMAT 165 CA Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 84

background image

Operation

ORBIMAT CA

| Operating instructions

36

orbitalum tools

GmbH, D-78224 Singen, www.orbitalum.com, Tel. +49 (0) 77 31 792-0

(09.03.15) OW_ORBIMAT_CA_BA_871060202_04_EN

8.2.6

Interrupting the welding process

Switching off entire system

X

Switch off machine at the main switch.

– or –

X

Press EMERGENCY-STOP button on connected remote control.

The entire machine is disconnected from the mains network immediately and completely (both poles). No other functions
are carried out here: The gas flow is interrupted immediately. The current weld becomes unusable.

Stopping a running process

X

Press softkey 1 ("Stop").

– or –

X

Press STOP button on connected remote control.

– or –

X

Press red START/STOP button on weld head.

The weld current is switched off immediately. The machine remains in operation, the gas post purge time runs and the
water cooling of the weld head is carried out until the end of the gas post purge time.
A slight crater can arise in the seam on the workpiece, and this can be compensated for by over-welding it.

Premature slope-off of a running process

X

Press softkey 2 ("Final slope").

– or –

X

Press the "Final" button on the weld head.

– or –

X

Press slope-off symbol on connected remote control.

The machine slopes off the weld current as per the procedure. The weld head continues running during the slope-off phase.
After slope-off, the weld current is switched off, the gas post purge and pump continue running until the end of the
programmed time.

8.3

Adjusting the procedure

8.3.1

Reasons and steps for adjusting procedure

The auto programming of the machine cannot take all influencing factors into account during welding.
Procedures can be adjusted after the test run for this reason. Possible reasons:

• Batch-dependent fluctuations in the material composition
• Different dissipation (pipe on solid parts) etc.

X

Improve procedure step by step. When adjusting, change only one parameter at a time so that you can better judge
the influence on welding.

X

Save adjusted procedure.

X

After the adjustment, carry out a test run of the parameters.

X

Observe effects of the adjustment and carry out further adjustments if necessary.

«
...
34
35
36
37
38
...
»

Содержание Orbitalum ORBIMAT 165 CA





















































































Отзывы:

Нет отзывов

Похожие инструкции для Orbitalum ORBIMAT 165 CA

Бренд: Bahco Страницы: 6

Бренд: Baileigh Страницы: 39

Бренд: Fein Страницы: 53

Бренд: Sealey Страницы: 3

Бренд: Landoll Страницы: 54

Бренд: EINHELL Страницы: 24

PSBEN 2024B/LCD

Бренд: Pulsar Страницы: 44

7539-300X Series

Бренд: Avdel Страницы: 47

Бренд: Kolver Страницы: 7

Бренд: Cantek Страницы: 29

Бренд: Fein Страницы: 25

Бренд: microjig Страницы: 22

Бренд: TDK-Lambda Страницы: 10

Бренд: WAGO Страницы: 2

Бренд: Excelsys Страницы: 74

Бренд: Pulsar Страницы: 8

Millipore mA700

Бренд: Merck Страницы: 9

Бренд: Extech Instruments Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды