ITW Orbitalum ORBIMAT 165 CA Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 84

background image

ORBIMAT CA

| Operating instructions

Operation

(09.03.15) OW_ORBIMAT_CA_BA_871060202_04_EN

orbitalum tools

GmbH, D-78224 Singen, www.orbitalum.com, Tel. +49 (0) 77 31 792-0

53

Example: 60 A is programmed for the high-pulse current in a sector. During the process, a value of 55 A (–5 A) is mea-
sured: A warning message appears ("

High-pulse current too low

"). The process continues running. The operator can

carry out other measures (e.g. manual initiation of current slope-off).

Maximum HP current (alarm)

Upward deviation of the high-pulse current (HP): If the specified deviation (5 A) is reached, a warning message appears.

Example: 60 A is programmed for the high-pulse current in a sector. During the process, a value of 65 A (+5 A) is measured:
A warning message appears ("

High-pulse current too high

"). The process continues running. The operator can carry out

other measures.

Maximum HP current (abort)

Upward deviation of the high-pulse current (HP): If the specified deviation (+10 A) is reached, welding is aborted.

Example: 60 A is programmed for the high-pulse current in a sector. During the process, a value of 70 A (+10 A) is mea-
sured: The process is aborted. The gas post purge time is still complied with.

This method of functioning applies for the following parameters in the same way:

•

Minimum/maximum LP current

•

Minimum/maximum HP speed

•

Minimum/maximum LP speed

Minimum/maximum voltage

The minimum and maximum deviations are not specified for the arc. The absolute voltage values are provided instead.
There is no setpoint value for the arc voltage in the procedure which can be compared to the current measured value.

Minimum/maximum voltage (abort)

Welding is aborted when the value is reached.

Minimum/maximum voltage (alarm)

A warning message appears when the value is reached.

«
...
51
52
53
54
55
...
»

Содержание Orbitalum ORBIMAT 165 CA





















































































Отзывы:

Нет отзывов

Похожие инструкции для Orbitalum ORBIMAT 165 CA

Бренд: Quasar Страницы: 3

Бренд: Premium Tool Страницы: 4

Бренд: HARDELL Страницы: 8

Бренд: Campbell Hausfeld Страницы: 2

GEN 8-400 ABCDE

Бренд: TDK-Lambda Страницы: 96

Бренд: Ford Страницы: 11

Бренд: Paslode Страницы: 24

Бренд: Skil Страницы: 128

Бренд: HARTING Страницы: 2

Бренд: Laguna Tools Страницы: 9

Бренд: Senco Страницы: 46

Бренд: Datcon Страницы: 32

Бренд: Parkside Страницы: 50

GREAT STUFF PRO 13

Бренд: Dow Страницы: 4

Бренд: Greenlee Страницы: 16

CR-60 Cornerounder

Бренд: Lassco Wizer Страницы: 10

Бренд: Xinpu Страницы: 14

Бренд: Alcoa Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды