ITW Orbitalum ORBIMAT 165 CA Скачать руководство пользователя страница 46

Страница: 46 / 84

Operation

ORBIMAT CA

| Operating instructions

orbitalum tools

GmbH, D-78224 Singen, www.orbitalum.com, Tel. +49 (0) 77 31 792-0

(09.03.15) OW_ORBIMAT_CA_BA_871060202_04_EN

8.4.2

Calling up a procedure

Recommendation:

Save unsaved procedures if necessary before calling up a procedure.

1. Press the "

Select procedure

" button in the main menu.

2. Select folder.

A list of procedures appears. Additional information on each procedure appears in the display.

3. Select procedure.

If an unsaved procedure is loaded in the RAM, another procedure cannot be loaded.
A warning appears:
"

Cancel

": The procedure call is interrupted. The main menu appears:

": The unsaved procedure is not saved, and any adjustments made are lost.

The selected procedure is called up.
"

Yes

": The unsaved procedure is saved. The main menu appears.

If unsaved procedures are saved or adjustments were rejected:

4. Call up procedure again.

The selected program appears in the display.

8.5

Locking machine with key switch

The machine features two views of the main menu:

Long form

Procedure programming mode. Procedures can be changed, and sensors and monitoring functions can be activated/deac-
tivated.

Short form

Production mode. All functions which lead to changes in the existing programs cannot be executed in the "Short menu"
and are not displayed. Sensors and monitoring functions cannot be deactivated.

Switching between the two views is carried out using the
key switch located on the front.

Key switch in "

disabled

" position:

Machine is locked; the main menu appears in

short form

in the display.

The saved data is largely protected against loss or change.

Recommendation

Create backup copies of the data of the internal
memory at regular intervals.

Fig. 22:

Main menu (Short form)

Содержание Orbitalum ORBIMAT 165 CA





















































































Результаты поиска

Содержание Orbitalum ORBIMAT 165 CA

Отзывы:

Похожие инструкции для Orbitalum ORBIMAT 165 CA

Бренды по названию

Популярные бренды

ITW Orbitalum ORBIMAT 165 CA, Руководство по эксплуатации

Результаты поиска

Содержание Orbitalum ORBIMAT 165 CA

Отзывы:

Похожие инструкции для Orbitalum ORBIMAT 165 CA

Бренды по названию

Популярные бренды