ITW Orbitalum ORBIMAT 165 CA Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 84

background image

Operation

ORBIMAT CA

| Operating instructions

62

orbitalum tools

GmbH, D-78224 Singen, www.orbitalum.com, Tel. +49 (0) 77 31 792-0

(09.03.15) OW_ORBIMAT_CA_BA_871060202_04_EN

Z

Copy folder to the top level of the memory card.

3. Push memory card into the card reader of the machine.

The diskette symbol appears in the display.

4. In the main menu, select "

System settings

" > "

Service

" > "

Import procedures

".

The folder structure of the machine appears in the display.

Z

To create a new folder, select "

New folder

", enter a name and confirm.

5. Select folder.

The data is transferred and converted in the internal memory of the machine. The original procedure names, comments
etc. remain in tact on the memory card.

8.17 Special keyboard commands

The following commands can be entered using the external keyboard:

VER

Display software version.

SER

Display service screen.

RES

Brings you back to the main menu and executes a "software reset" if software-related problems are occurring
(also possible via simultaneous pressing of softkeys 1 + 5).

ERR

Printing/deletion of system error messages.

SLO

Switches the slope representation from % (standard) to seconds.

8.18 Operation of the system with other mains voltages (OM 165 CA only)

The OM 165 CA machine features a "wide range" input for the mains voltage (input voltage).
The machine can be set in the voltage range from 90 - 260 V at a frequency of 50 - 60 Hz.
For operation on e.g. 115 V (or any other voltage in the range stated above), the operator does not need to switch any-
thing or make any settings or adjustments.
In 115 V operation, higher input currents arise with otherwise even loading of the machine. The weld current is auto-
matically limited to 100 A if a mains voltage of less than 200 V is active.

The machine detects the mains voltage automatically and does not permit currents over 110 A to be entered when pro-
gramming the system.
Procedures containing current values over 110 A cannot be started.

X

Ensure that an appropriate power plug is used for the power connection.

X

Have the power plug changed if necessary.

«
...
60
61
62
63
64
...
»

Содержание Orbitalum ORBIMAT 165 CA





















































































Отзывы:

Нет отзывов

Похожие инструкции для Orbitalum ORBIMAT 165 CA

Бренд: Gallagher Страницы: 40

Бренд: Felisatti Страницы: 28

Bristle Blaster Pneumatic

Бренд: Monti Страницы: 268

Бренд: Gallagher Страницы: 22

SOLARLOK PN 1-1579004-1

Бренд: TE Connectivity Страницы: 47

Бренд: Neilsen Страницы: 16

Бренд: M-system Страницы: 2

Бренд: Goobay Страницы: 10

Бренд: IAN CANADA Страницы: 15

Бренд: GOAL ZERO Страницы: 40

Бренд: Ingersoll-Rand Страницы: 57

Бренд: Calortrans Страницы: 11

Бренд: Meec Страницы: 20

Бренд: Anritsu Страницы: 4

Бренд: Power Inspired Страницы: 4

Smart Cord UTBF07SG-110

Бренд: Emerge Страницы: 4

Optiworx HW Series

Бренд: C-COR Страницы: 36

Бренд: Makita Страницы: 103

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды