ITW Orbitalum ORBIMAT 165 CA Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 84

background image

Servicing, maintenance, troubleshooting

ORBIMAT CA

| Operating instructions

78

orbitalum tools

GmbH, D-78224 Singen, www.orbitalum.com, Tel. +49 (0) 77 31 792-0

(09.03.15) OW_ORBIMAT_CA_BA_871060202_04_EN

10. SERVICING, MAINTENANCE, TROUBLESHOOTING

10.1 Maintenance

DANGER

Dangers of improper maintenance of the system!

Various injuries and damage to property.

X

Carry out maintenance as described in the "Maintenance" chapter.

DANGER

Improper access to and opening of the ORBIMAT machine!

Electric shock.

X

Disconnect machine from mains.

X

Disconnect all external devices connected to the machine (weld heads etc.).

X

Allow machine to cool down sufficiently before opening.

X

Allow only a professional electrician to access the electrical system.

[

Never

connect an opened system to the mains network.

10.1.1

Maintenance intervals

Time/Interval Activity

Daily

X

Check water level in tank (OM 165 CA) or in external cooling unit (OM 300 CA) and fill if necessary.

Frequent refilling of the coolant may be necessary if the weld heads are changed frequently.
1. After exchanging the weld head make sure that the weld head is completely filled with coolant (al-

low the weld head to run for approx. 3 mins. – key: GAS/water).

2. Check coolant level and refill if necessary.

X

If anti-freeze is used: Supplement with water appropriately.

X

Wipe off display with a slightly damp cloth. Do not use cleaning agents.

Monthly

X

Clean machine fully from the outside.

X

Check power cable, power plug and machine for mechanical damage.

X

Clean weld heads and check mains cable.

Recommendation:

X

Carry out motor calibration (even if the weld heads are suspected to be running properly).

Semiannually 1. Pump out all coolant.

2. Add fresh tap water and pump out all of this filling as well.
3. Fill tank with coolant OCL-15.

Annually

Recommendation:

X

Have machine maintenance carried out once annually by Orbitalum or a service point authorized by
Orbitalum if it is in constant use.

X

Carry out the following maintenance work:

1.  Open unit and clean inside (compressed air).
2.  Carry out visual check (hoses, seals, loose parts etc.).
3.  Clean water filter (OM 300 CA only).
4.  Performance of the prescribed measurements for electrical safety of the machine (incl. log).
5.  Carry out current calibration incl. log.
6.  Carry out full machine test with all functions.

After 3 years

X

Replace buffer battery (PC).

«
...
76
77
78
79
80
...
»

Содержание Orbitalum ORBIMAT 165 CA





















































































Отзывы:

Нет отзывов

Похожие инструкции для Orbitalum ORBIMAT 165 CA

Бренд: SafetySpeed Страницы: 43

DC POWER-L Series

Бренд: Salicru Страницы: 32

SPD1000X Series

Бренд: SIGLENT Страницы: 24

GREEN POWER CCTV BNC04124

Бренд: Pulsar Страницы: 8

BANDSAW BLADE SHARPENER

Бренд: Woodland Mills Страницы: 56

Бренд: Kilews Страницы: 14

Бренд: Hama Страницы: 36

Бренд: Wen Страницы: 2

Бренд: Ingersoll-Rand Страницы: 23

Бренд: Skil Страницы: 60

Бренд: Maddox Страницы: 8

SonnenProtect 1300-AU-IN-ATS

Бренд: Sonnen Страницы: 20

SMA 20 APF-25.L1

Бренд: Gerima Страницы: 22

Бренд: Deprag Страницы: 40

Бренд: LionTec Страницы: 5

Бренд: Cutech Страницы: 40

Бренд: RS PRO Страницы: 31

Бренд: Parkside Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды