ICON ICON-500 Series Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 110

ICON500 high performance vector control frequency inverter user
manual

Chapter6 Fault diagnosis and
solutions

-
91-

Fault Name

Display

Possible Causes

Solutions

Over current

during

deceleration

Er.OC2

1: The output circuit is grounded or
short circuited.
2: Motor auto-tuning is not performed.
3: The deceleration time is too short.
4: The voltage is too low.
5: A sudden load is added during
deceleration.
6: The braking unit and braking
resistor are not installed

1: Eliminate external faults.
2: Perform the motor
auto-tuning.
3: Increase the decelerationtime.
4: Adjust the voltage to normal
range.
5: Remove the added load.
6: Install the braking unit
Andbraking resistor.

Over current

at constant

speed

Er.OC3

1: The output circuit is grounded or
short circuited.
2: Motor auto-tuning is notperformed.
3: The voltage is too low.
4: A sudden load is added during
operation.
5: The frequency inverter model is of
too small power class.

1:Eliminateexternalfaults.
2: Perform themotorauto-tuning.
3:AdjustThevoltagetonormalrange.
4: Remove the addedload.
5: Select afrequency
Inverterofhigher powerclass.

Overvoltage

during

acceleration

Er.OU1

1: The input voltage is too high.
2: An external force drives the motor
during acceleration.
3: The acceleration time is too short.
4: The braking unit and braking
resistor are not installed.

1:AdjustThevoltagetonormalrange.
2: Cancel theexternal forceor
install a braking resistor.
3: Increasethe accelerationtime.
4: Install thebraking unit
Andbraking resistor.

Overvoltage

during

deceleration

Er.OU2

1: The input voltage is too high.
2: An external force drives the motor
during deceleration.
3: The deceleration time is too short.
4: The braking unit and braking
resistor are not installed.

1:AdjustThevoltagetonormal
Range.
2: Cancel theexternal forceor
install thebraking resistor.
3: Increasethe decelerationtime.
4: Install thebraking unit
Andbraking resistor

Overvoltage

at constant

speed

Er.OU3

1: The input voltage is too high.
2: An external force drives the motor
during deceleration.

1:AdjustThevoltagetonormalrange.
2: Cancel theexternal forceor
install thebraking resistor.

Low voltage

Er.LU1

1: Instantaneous power failure occurs
on the input power supply.
2: The frequency inverter's input
voltage is not within the allowable
range.
3: The DC bus voltage is abnormal.
4: The rectifier bridge and buffer
resistor are faulty.
5: The drive board is faulty.
6: The main control board is faulty.

1: Reset thefault.
2:Adjust
Thevoltagetonormalrange.
3: Ask for technical support
4: Ask for technical support
5: Ask for technical support
6: Ask for technical support

«
...
92
93
94
95
96
...
»

Содержание ICON-500 Series















































































































Отзывы:

Нет отзывов

Похожие инструкции для ICON-500 Series

Easy Drive CFW10

Бренд: WEG Страницы: 2

MILLENIUM 1100-46D

Бренд: York Страницы: 24

Бренд: Ltech Страницы: 7

Бренд: Beckhoff Страницы: 208

Бренд: Bosch Страницы: 50

Бренд: Bosch Страницы: 66

rexroth Servodyn-D

Бренд: Bosch Страницы: 72

MSK030B NSNN Series

Бренд: Bosch Страницы: 178

MSK030B-0900-NN

Бренд: Bosch Страницы: 282

Бренд: Siemens Страницы: 10

SINAMICS V20 Inverter

Бренд: Siemens Страницы: 28

Бренд: Siemens Страницы: 122

Бренд: Siemens Страницы: 132

SINAMICS SM150 6SL3815-7NP41-0AA1

Бренд: Siemens Страницы: 198

Бренд: Siemens Страницы: 218

SINAMICS V20 Inverter

Бренд: Siemens Страницы: 426

SINAMICS V20 Series

Бренд: Siemens Страницы: 274

Бренд: Cole Parmer Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды