Huawei UPS5000-S-1200 kVA Скачать руководство пользователя страница 208

Страница: 208 / 215

UPS5000-S-1200 kVA
User Manual

10 Alarm List

Issue 04 (2019-06-25)

200

Alarm ID
(Alarm
ID-Cause
ID)

Alarm Name Severity

Cause

Solution

bypass input circuit breaker 10 seconds
later.

0564-1

Overload
timeout

Critical



The load is
excessive.



Derating
reduces the
rated system
power.



The module
is damaged.



The output is
incorrectly
grounded.

Check that there is no overload.

Check that the module power is not
derated due to a fan fault.

Check whether the power grid has a
large asymmetric load.

Check whether the output is grounded.

If the alarm persists, replace the power
module.

0565-1

Load impact
transfer-to-byp
ass

Minor



A
large-power
RCD load is
instantly
connected, or
the output
load
short-circuits.



The inverter
bridge
short-circuits.

Check the load.

If the load is normal, replace the power
module.

0566-1

Output
overload

Minor



The load is
excessive.



Derating
reduces the
rated system
power.



The module
is damaged.

Check that there is no overload.

Check that the module power is not
derated due to a fan fault.

If the alarm persists, replace the power
module.

0570-4

BPM module
abnormal

Critical



The bypass
fan is not
functioning
properly, or
the air
channel is
blocked.



The ambient
temperature
exceeds the
upper
threshold.



The load is

Check the bypass fan and air channel. If
the fan is faulty, replace it.

Check that the ambient temperature has
not exceeded 40°C.

Check that there is no overload.

Содержание UPS5000-S-1200 kVA
























































































































































































































Результаты поиска

Содержание UPS5000-S-1200 kVA

Отзывы:

Похожие инструкции для UPS5000-S-1200 kVA

Бренды по названию

Популярные бренды

Huawei UPS5000-S-1200 kVA, Руководство пользователя

Результаты поиска

Содержание UPS5000-S-1200 kVA

Отзывы:

Похожие инструкции для UPS5000-S-1200 kVA

Бренды по названию

Популярные бренды