Huawei UPS5000-S-1200 kVA Скачать руководство пользователя страница 145 | Manualshive

Страница: 145 / 215

background image

UPS5000-S-1200 kVA
User Manual

4 User Interface

Issue 04 (2019-06-25)

Copyright © Huawei Technologies Co., Ltd.

137

Item

Description

Default Value Value Range

cannot enter the ECO mode. If
this parameter is set to

Enable

,

the preceding detection is not
performed. Whether the bypass
current is imbalanced does not
affect the ECO bypass mode.

Battery Settings

Battery parameter settings impact battery maintenance, battery lifespan, and UPS discharge
time. When you set battery parameters, note the following:



Retain default settings for

Chg. cur. limiting coef.

and

Cell float voltage

. Only

professional maintenance personnel are allowed to change the settings.



When you set parameters, ensure the following:

Chg. cur. limiting coef.

>

Transfer-to-equalized charging cur. coef

.



Single batt. float chg. voltage deviation alarm thres.

and

Single batt. dis. voltage

deviation alarm thres.

are used to check whether the batteries in each battery string have

the same charge voltage and discharge voltage. When a value exceeds the specified range,
an alarm is generated. The calculation formula is (Charge/Discharge voltage – Average
voltage)/Average voltage x 100%. The charge/discharge voltage and average voltage are
obtained from the BMU. If the BMU is not configured, these two parameters do not need
to be set.

Item

Description

Default Value Value Range

Float volt.
temp. comp.

If this parameter is set to

Enable

,

the float voltage is calibrated
based on the battery temperature
when a battery temperature
sensor is connected. The
parameter is configurable in any
mode.

Enable

Disable, Enable

Float volt.
temp. comp.
coef.
(mV/°C·cell)

Calibration coefficient during
float voltage temperature
compensation.

3.3

0.0–6.0

Float Chg
Temp Comp
Center (°C)

Indicates the reference
temperature during temperature
compensation of the float
charging voltage.

25

20–30

Automatic
equalized
charging

If this parameter is set to

Enable

,

the UPS automatically changes
the battery management status to
equalized charge based on the

Enable

Disable, Enable

«
...
143
144
145
146
147
...
»

Содержание UPS5000-S-1200 kVA
























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для UPS5000-S-1200 kVA

Бренд: Varec Страницы: 74

Бренд: Halyard Страницы: 84

Бренд: PAIDI Страницы: 48

Бренд: ZIGBEE Страницы: 4

Бренд: CAIRE Страницы: 38

Бренд: Caframo Страницы: 72

Pro Vantage 12+ Series

Бренд: Ecco Страницы: 6

Бренд: Federal Signal Corporation Страницы: 4

Бренд: FASTERHOLT Страницы: 96

Бренд: SandenVendo Страницы: 19

RZN 43-E Series

Бренд: D+H Страницы: 2

Бренд: Vaillant Страницы: 76

Бренд: H2flow Страницы: 2

Бренд: V-TAC Страницы: 27

Бренд: Yacht Sentinel Страницы: 32

Бренд: X-FLOC Страницы: 35

univers N UC21LH1

Бренд: hager Страницы: 13

univers N UK31LH1FM

Бренд: hager Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды