Huawei UPS5000-H-400 kVA Скачать руководство пользователя страница 56

Страница: 56 / 175

Figure 5-5 Ports on the backfeed protection card

Table 5-2 Port description for the backfeed protection card

Port Position Silk Screen

Signal Description

MFP (mains

feedback

protection)

MFP_NO

The MFP port is the signal port for the mains

backfeed protection. NO and COM are normally

open contacts. NC and COM are normally closed

contacts. When a backfeed occurs, the normally

open contacts are closed and the normally closed

contacts are open.

MFP_COM

MFP_NC

BFP (bypass

feedback

protection)

BFP_NO

The BFP port is the signal port for the bypass

backfeed protection. NO and COM are normally

open contacts. NC and COM are normally closed

contacts. When a backfeed occurs, the normally

open contacts are closed and the normally closed

contacts are open.

BFP_COM

BFP_NC

RSV

(reserved)

RSV_NO

Reserved

RSV_COM

RSV_NC

5.4 Intelligent Detection Card

In the integrated UPS solution, the intelligent detection card detects the

temperatures of the copper bars, switches, and environments of the battery,

bypass input, mains input, output, bypass input of the switch cabinet, mains input

of the switch cabinet, and output of the switch cabinet, and monitors the status of

the mains input, bypass input, and output switches of the switch cabinet.
It is 1 U high and supports hot swap.

UPS5000-H-(400 kVA-800 kVA)

User Manual (100 kVA Power Module)

5 Optional Components

Issue 02 (2021-04-22)

Содержание UPS5000-H-400 kVA
















































































































































































Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды

Huawei UPS5000-H-400 kVA, Руководство пользователя

Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды