Huawei UPS5000-H-400 kVA Скачать руководство пользователя страница 144 | Manualshive

Страница: 144 / 175

background image

NO TICE

Before capacity expansion, ensure that:
● The new UPS has the same software version as all running UPSs.
● The input and output cable connections and phase sequence of the new UPS

are correct. The mains input switch, bypass input switch, and output switch are

OFF.

● The parallel cable of the new UPS is not connected.
● Before connecting inter-rack parallel cables for the new UPS and the original

UPSs in the system, set parallel parameters and ensure that parallel IDs do not

conflict.

Step 1 Commission the new UPS by following the instructions in

7.1 Powering On and

Starting the UPS

. During the commissioning, do not switch on the external

output circuit breaker. After the commissioning is complete, the UPS shuts down

and transfers to bypass mode. Ensure that the external output circuit breaker is

OFF.

Step 2 Check that the bypass phase sequence of the new UPS and the original UPSs is

correct.
1. Ensure that no abnormal bypass alarm is generated on all the UPSs in the

system (including the new UPS). Then, the original UPSs and the new UPS

work in bypass mode.

2. Set the multimeter to the AC voltage position, connect the red probe to phase

A at the front end of the external output switch of the new UPS, and connect

the black probe to phase A at the back end of the external output switch of

the new UPS to measure the voltage difference. Perform the same operations

on phases B and C. If the phase sequence is correct and the voltage difference

is less than 5 V, perform the subsequent operations. If the phase sequence is

incorrect or the voltage difference for any phase is greater than 5 V, power off

the new UPS completely, and check whether the bypass input cable for the

UPS is properly connected.

Step 3 If the original system is a single UPS system, check whether the current version

supports a parallel system. If a parallel system is not supported, upgrade the

software to support the parallel system.

Step 4 Set parallel parameters for the original system.

●

If the original system is a single UPS system, see

8.1 Starting a

Parallel System

.

●

If the original system is a parallel system, change the Requisite UPSs and

Redundant UPSs on each UPS of the original system so that the sum of

Requisite UPSs and Redundant UPSs is equal to the total number of original

parallel UPSs plus the number of new UPSs.

NO TE

The system may generate alarms such as Rack quantity mismatch, Insufficient

redundant racks, and Inter-rack par. cable alarm. The alarms are automatically cleared 1

minute after you connect all parallel cables.

Step 5 Set parallel parameters for the new UPS.

UPS5000-H-(400 kVA-800 kVA)

User Manual (100 kVA Power Module)

8 Parallel System Commissioning

Issue 02 (2021-04-22)

Copyright © Huawei Technologies Co., Ltd.

136

«
...
142
143
144
145
146
...
»

Содержание UPS5000-H-400 kVA
















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для UPS5000-H-400 kVA

Бренд: Quasar Страницы: 3

Бренд: Dake Страницы: 24

Бренд: Pulsar Страницы: 40

Бренд: Mitox Страницы: 40

Бренд: GEM Страницы: 2

Бренд: Panduit Страницы: 2

Бренд: Xantrex Страницы: 76

Бренд: King Canada Страницы: 6

Бренд: Dawson Страницы: 63

Бренд: N2Power Страницы: 10

Бренд: BE QUIET! Страницы: 51

Бренд: YOKOGAWA Страницы: 2

Бренд: Beckhoff Страницы: 57

Бренд: YATO Страницы: 64

Бренд: Nortel Страницы: 28

Бренд: YAKUMO Страницы: 63

Бренд: IMI NORGREN Страницы: 11

Бренд: Meec Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды