Huawei UPS5000-H-400 kVA Скачать руководство пользователя страница 112

Страница: 112 / 175

No.

Item

Acceptance Criteria

Neat arrangement

The UPS and its adjacent cabinets are

neatly arranged and secured with

connecting kits.

Layout of the busway and

cables

The busway and cables are routed

properly as required by the customer.

Labels on the busway and

cables

Both ends of a busway and cable are

labeled. Labels are concise and easy to

understand.

Cable ties

Cable ties are secured evenly and no burr

exists.

Cable and busbar

connections

Input power cables or busbars, output

power cables or busbars, and cables

between batteries are securely

connected. For the cables secured by

screws, the spring washers are flattened.

Grounding

The resistance between the UPS ground

bar and the equipment room ground bar

is less than 0.1 ohm.

AC phase sequence

The mains input, bypass input, and

output phase sequences are correct.

Battery cable connections

The battery strings are correctly

connected to the UPS.

Foreign matter cleaning

inside the cabinets

The inside and outside of the cabinets

are free from conductive dust or other

sundries.
1. There is no foreign matter (such as

copper wires and screws) on the top

of the cabinets.

2. There is no foreign matter on the

copper bar terminals.

3. There is no foreign matter around

switch terminals.

4. There is no foreign matter on the

bottom plates of the cabinets.

5. There is no foreign matter on the rear

module subrack.

UPS5000-H-(400 kVA-800 kVA)

User Manual (100 kVA Power Module)

6 Installation

Issue 02 (2021-04-22)

104

Содержание UPS5000-H-400 kVA
















































































































































































Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды

Huawei UPS5000-H-400 kVA, Руководство пользователя

Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды