Huawei UPS5000-H-400 kVA Скачать руководство пользователя страница 19

Страница: 19 / 175

NO TICE

● This is a category C3 UPS product for commercial and industrial application in

the second environment − installation restrictions or additional measures may

be needed to prevent disturbances.

● After unpacking the UPS, you are advised to power on the UPS as soon as

possible. If you temporarily do not use the UPS, take appropriate measures to

prevent moisture, dust, and foreign matter from entering the UPS.

● After unpacking batteries, you are advised to connect the battery supply as

soon as possible. If you temporarily do not use the batteries, store them in a

dry and clean environment. If batteries are stored for more than 90 days,

charge them in time. Otherwise, the battery lifespan may be affected.

● Install the UPS in an area far away from liquids. Do not install it under areas

prone to water leakage, such as air conditioner vents, ventilation vents, or

feeder windows of the equipment room. Ensure that no liquid enters the UPS

to prevent short circuits. Ensure that there is no condensation inside the

equipment or equipment room.

● If any liquid is detected inside the equipment, immediately disconnect the

power supply and contact the administrator.

D ANGER

● Do not expose the equipment to flammable or explosive gas or smoke. Do not

perform any operation on the equipment in such environments.

● During installation and maintenance, ensure that sundries do not enter the

UPS. Otherwise, equipment damage, load power derating, power failure, and

personal injury may occur.

If the valid mains voltage exceeds 320 V AC, the UPS may be damaged.

A UPS can be used to serve resistive-capacitive loads, resistive loads, and micro-

inductive loads. It is recommended that a UPS not be used for pure capacitive

loads, pure inductive loads, and half-wave rectification loads. A UPS does not

apply to regeneration loads.

Any operation on any electrical device in an environment that has inflammable air

can cause extreme danger. Strictly obey the operating environmental requirements

specified in related user manuals when using or storing the device.

The UPS can be configured with a backfeed protection dry contact to work with

an external automatic circuit breaker, preventing the voltage from flowing back to

input terminals over static bypass circuits. If the installation and maintenance

personnel do not need backfeed protection, paste labels on external mains and

bypass input switches, informing that the UPS is connected to a backfeed

protection card. Disconnect the backfeed protection card from the UPS before

operating the UPS.

Do not use the UPS in the following places:

UPS5000-H-(400 kVA-800 kVA)

User Manual (100 kVA Power Module)

1 Safety Information

Issue 02 (2021-04-22)

Содержание UPS5000-H-400 kVA
















































































































































































Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды

Huawei UPS5000-H-400 kVA, Руководство пользователя

Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды