Huawei UPS5000-H-400 kVA Скачать руководство пользователя страница 44

Страница: 44 / 175

Silk Screen

Signal Description

Status

Description

Initial

Status

SWITCH

STATUS_MT

Port for monitoring the

maintenance switch

● Open: The

maintenance

switch is ON.

● Closed: The

maintenance

switch is OFF.

Open

SWITCH

STATUS_0V

Port for signal ground

SWITCH

STATUS_BP

Port for monitoring the

bypass input circuit breaker

● Closed: The

bypass input

circuit breaker

is ON.

● Open: The

bypass input

circuit breaker

is OFF.

Closed

SWITCH

STATUS_0V

Port for signal ground

SPD

Port for monitoring the

input AC SPD

● Closed: The

input AC SPD is

normal.

● Open: The input

AC SPD fails.

Closed

Port for signal ground

a: On the LCD, choose System Info > Settings > System Settings > Dry

Contact Set > MUE05A DI type configure, and customize the initial status of

Battery ground fault [BTG], D.G. connection [GEN], PDC output breaker

[OUT], PDC maintenance breaker [MT], BP/SYSMT switch, and SPD/SYSOUT

switch.

4.3.4 Monitoring Interface Card

The monitoring interface card provides external ports as well as monitoring and

control functions for the MDU. The monitoring interface card provides the

ambient temperature and humidity sensor port, FE port, battery temperature

monitoring port, and network management port. The MDU monitors the UPS,

allows users to set parameters, delivers commands, reports system information,

and displays key UPS information and parameters on the LCD.

UPS5000-H-(400 kVA-800 kVA)

User Manual (100 kVA Power Module)

4 Component Description

Issue 02 (2021-04-22)

Содержание UPS5000-H-400 kVA
















































































































































































Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды

Huawei UPS5000-H-400 kVA, Руководство пользователя

Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды