Huawei UPS5000-H-400 kVA Скачать руководство пользователя страница 120

Страница: 120 / 175

NO TE

If MUE06A connection is set to Enable and the backfeed protection card fails to

communicate with the UPS, the system reports a Dry contact board fault alarm.

----End

7.1.8 (Optional) Setting the Intelligent Detection Card

Prerequisites

An intelligent detection card is installed.

Procedure

Step 1 On the LCD, choose System Info > Settings > System Settings and set

Intelligent detection module to Enable.

----End

7.2 Shutting Down and Powering Off the UPS

Context

NO TICE

If the bypass is normal, the UPS transfers to bypass mode after the inverter is shut

down; if the bypass is abnormal, the UPS supplies no power after the inverter is

shut down. Before shutting down the UPS, ensure that all loads have been shut

down.

Procedure

Step 1 Shut down the inverter.

●

Shutting down the inverter on the LCD
Choose Common Functions > Inv. OFF. After confirmation, the inverter is

shut down.

NO TE

You can also choose System Info > Maintenance > Inv. OFF to shut down the

inverter.

●

Shutting down the inverter on the WebUI
Choose Monitoring > UPS System > Running Control, and click Inv. OFF.

If the inverter shuts down and the bypass is normal, the UPS transfers to bypass

mode. The Bypass mode alarm is displayed on the LCD.

UPS5000-H-(400 kVA-800 kVA)

User Manual (100 kVA Power Module)

7 Single UPS Commissioning

Issue 02 (2021-04-22)

112

Содержание UPS5000-H-400 kVA
















































































































































































Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды

Huawei UPS5000-H-400 kVA, Руководство пользователя

Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды