Huawei UPS5000-H-400 kVA Скачать руководство пользователя страница 73

Страница: 73 / 175

Item

600 kVA

700 kVA

800 kVA

Battery input

(SmartLi)

Nominal battery

discharge current (A)

1234

1439

1645

Maximum battery

discharge current (A)

1547

1806

2064

Recommended cross-

sectional area

For details, see the IEC-60364-5-52 specifications and

SmartLi User Manual

Equipotential

ground point

Recommended cross-

sectional area (mm

)

NO TE

The rated voltage of the SmartLi is 512 V. The voltage is 408 V at the maximum discharge

current.

●

The currents listed in the table are measured at a rated voltage of 380 V.

●

When selecting, connecting, and routing power cables, follow local safety

regulations and rules.

●

When the external conditions such as the cable layout or ambient

temperatures change, perform verification in accordance with the IEC

60364-5-52 or local regulations.

●

For the 400 V rated voltage, multiply the current by 0.95.

●

For the 415 V rated voltage, multiply the current by 0.92.

●

When the primary loads are non-linear loads, increase the cross-sectional

areas of the neutral wires to 1.5–1.7 times.

●

The nominal battery discharge current refers to the current of forty 12 V

batteries at 480 V in standard configuration.

●

The maximum battery discharge current refers to the current when forty 12 V

batteries in standard configuration, that is, two hundred and forty 2 V battery

cells (1.67 V/cell), stop discharging.

●

The battery cable specifications are selected based on 40 batteries by default

and compatible with application scenarios with 30–50 batteries.

●

When the mains input and bypass input share a power source, configure

mains input power cables as input power cables. In addition, cables

recommended in the table apply only when the following requirements are

met:
–

Routing mode: The cables are routed over a tray or bracket in a single

layer (E in IEC 60364-5-52). The distance between cables should be

greater than twice the cable diameter. Routing mode: The cables are

routed over a tray or bracket in a single layer (E multi-core and G single-

core in IEC 60364-5-52).

–

The ambient temperature is 30°C.

–

The AC voltage loss is less than 3%, and the DC voltage loss is less than

1%.

UPS5000-H-(400 kVA-800 kVA)

User Manual (100 kVA Power Module)

6 Installation

Issue 02 (2021-04-22)

Содержание UPS5000-H-400 kVA
















































































































































































Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды

Huawei UPS5000-H-400 kVA, Руководство пользователя

Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды